參數資料
型號： TPS2392DBT
廠商： Texas Instruments, Inc.
英文描述： Utillity Helmet with Headband; RoHS Compliant: NA
中文描述： 全功能- 48 - V熱風全系統電源管理器
文件頁數： 24/31頁
文件大?。?/td> 373K
代理商： TPS2392DBT
SLUS536C AUGUST 2002 REVISED AUGUST 2004
www.ti.com
24
APPLICATION INFORMATION
using the PG output
The PG output is an indication of the load power status. PG is asserted after a load turn-on, once the load
voltage has ramped up to the input dc level, as indicated by a small VDS drop across the pass FET. The load
voltage is sensed by the DRAINSNS pin, which is connected to the pass FET drain through a small-signal
blocking diode. Also, the TPS2392 and TPS2393 first confirm that the full programmed sourcing current
(typically 40 mV/R
SENSE
) is available to the load electronics prior to declaring power good. The PG status is
latched once the power conditions are met, so that momentary current limiting operation due to input supply
transients is not reflected in this output status. This pin can be used to enable downstream converters, provide
a visual indication of load power good, or be level-translated or optocoupled to provide status reporting back
to the host controller.
When using PG to drive the enable input of a converter, care should be taken not to exceed the manufacturer’s
maximum voltage ratings for the pin. When asserted, the output driver pulls the PG pin to the VIN pin potential.
Because this status in latched, subsequent current limit operation of the circuit could result in pulling the enable
input below the brick’s VIN potential during the fault timeout period. If the brick does not provide an internal
clamp on this pin, a diode can be connected as shown in Figure 28 to externally limit the swing below VIN.
In either case, a resistor (R7 in Figure 28) should be used to limit the current pulled from this pin, protecting
both the converter and the PG output. R7 should be large enough to limit the PG input current to less than
10 mA, while still allowing the brick enable to be pulled below its maximum V
IL
threshold.
10
μ
A
UDG20177
GATE
ISENS
DRNSNS
RSENSE
VOUT+
VDD
VOUT
VIN+
VIN
DC/DC
CONVERTER
Q1
VIN
D1
BAS19
RTN
D3
R7
43 k
TPS2392*
TPS2393*
CIN
EN
48 V
GND
PG
*Additional details omitted for clarity.
See block diagram on page 15 and 16 for pinout.
Figure 29. TPS2392/TPS2393 Active-Low Converter Enable
相關PDF資料
PDF描述
TPS2393DBTR CLOTH ROLL, 25MX25MM, P240; Grit size:P240; Length:25m; Width, external:25mm RoHS Compliant: NA
TPS2534 Dual Channel Thermopile
TPS2848PWPR 30V N-Channel PowerTrench MOSFET
TPS2849PWPR 30V N-Channel PowerTrench MOSFET
TPS2839PWPR 30V N-Channel PowerTrench MOSFET
相關代理商/技術參數
參數描述
TPS2392EVM 功能描述:電源管理IC開發工具 Simple -48V Hot Swap Contr EVM RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
TPS2392PW 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2392PWG4 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2392PWR 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
TPS2392PWRG4 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*