- 您現在的位置：買賣IC網 > PDF目錄385011 > TPS2392DBT (Texas Instruments, Inc.) Utillity Helmet with Headband; RoHS Compliant: NA PDF資料下載
參數資料
| 型號： | TPS2392DBT |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | Utillity Helmet with Headband; RoHS Compliant: NA |
| 中文描述： | 全功能- 48 - V熱風全系統電源管理器 |
| 文件頁數： | 20/31頁 |
| 文件大?。?/td> | 373K |
| 代理商： | TPS2392DBT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
SLUS536C AUGUST 2002 REVISED AUGUST 2004
www.ti.com
20
APPLICATION INFORMATION
setting the sense resistor value
Due to the currentlimiting action of the internal LCA, the maximum allowable load current for an implementation
is easily programmed by selecting the appropriate sense resistor value. The LCA acts to limit the sense voltage
V
I(ISENS)
to its internal reference. Once the voltage at the IRAMP pin exceeds approximately 4 V, this limit is
the clamp voltage, V
REF_K
. Therefore, a maximum sense resistor value can be determined from equation (1).
33 mV
IMAX
R
SENSE
where:
R
SENSE
is the resistor value
IMAX is the desired current limit
When setting the sense resistor value, it is important to consider two factors, the minimum current that may
be imposed by the TPS2392 or TPS2393, and the maximum load under normal operation of the module. For
the first factor, the specification minimum clamp value is used, as seen in equation (1). This method accounts
for the tolerance in the sourced current limit below the typical level expected (40 mV/R
SENSE
). (The clamp
measurement includes LCA input offset voltage; therefore, this offset does not have to be factored into the
current limit again.) Second, if the load current varies over a range of values under normal operating conditions,
then the maximum load level must be allowed for by the value of R
SENSE
. One example of this is when the load
is a switching converter, or brick, which draws higher input current, for a given power output, when the
distribution bus is at the low end of its operating range, with decreasing draw at higher supply voltages. To avoid
current-limit operation under normal loading, some margin should be designed in between this maximum
anticipated load and the minimum current limit level, or IMAX > I
LOAD(max)
, for equation (1).
For example, using a 20-m
sense resistor for a nominal 1-A load application provides a minimum of 650 mA
of overhead for load variance/margin. Typical bulk capacitor charging current during turn-on ia 2 A
(40 mV/20 m
).
setting the inrush slew rate
The TPS2392/93 devices enable user-programming of the maximum current slew rate during load start-up
events. A capacitor tied to the IRAMP pin (C1 in the typical application diagram) controls the di/dt rate. Once
the sense resistor value has been established, a value for ramp capacitor C
IRAMP
, in microfarads, can be
determined from equation (2).
C
IRAMP
11
100
R
SENSE
di
dt
MAX
where:
R
SENSE
is the sense resistor value in
(di/dt)
MAX
is the desired maximum slew rate in A/s
For example, if the desired slew rate for the typical application shown is 1500 mA/mS, the calculated value for
C
IRAMP
is about 3700 pF. Selecting the next larger standard value of 3900 pF (as shown in the diagram) provides
some margin for capacitor and sense resistor tolerances.
As described in the Detailed Description section of this datasheet, the TPS2392 and TPS2393 initiate ramp
capacitor charging, and consequently, load current di/dt at a reduced rate. This reduced rate applies until the
voltage on the IRAMP pin is about 0.5 V. The maximum di/dt rate, as set by equation (2), is effective once the
device has switched to the 10-
μ
A charging source.
(1)
(2)
相關PDF資料 |
PDF描述 |
|---|---|
| TPS2393DBTR | CLOTH ROLL, 25MX25MM, P240; Grit size:P240; Length:25m; Width, external:25mm RoHS Compliant: NA |
| TPS2534 | Dual Channel Thermopile |
| TPS2848PWPR | 30V N-Channel PowerTrench MOSFET |
| TPS2849PWPR | 30V N-Channel PowerTrench MOSFET |
| TPS2839PWPR | 30V N-Channel PowerTrench MOSFET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS2392EVM | 功能描述:電源管理IC開發工具 Simple -48V Hot Swap Contr EVM RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| TPS2392PW | 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2392PWG4 | 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2392PWR | 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
| TPS2392PWRG4 | 功能描述:熱插拔功率分布 Full Featured -48V Industral Temp. RoHS:否 制造商:Texas Instruments 產品:Controllers & Switches 電流限制: 電源電壓-最大:7 V 電源電壓-最小:- 0.3 V 工作溫度范圍: 功率耗散: 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。