- 您現在的位置：買賣IC網 > PDF目錄98278 > TPIC8101DWRG4 (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PDSO20 PDF資料下載
參數資料
| 型號： | TPIC8101DWRG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO20 |
| 封裝： | GREEN, PLASTIC, SOIC-20 |
| 文件頁數： | 23/23頁 |
| 文件大?。?/td> | 511K |
| 代理商： | TPIC8101DWRG4 |
TPIC8101
KNOCK SENSOR INTERFACE
SLIS110A APRIL 2003 REVISED MAY 2005
9
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
description of the functional terminals (continued)
oscillator input (XIN)
The XIN terminal is the input to the inverter used for the oscillator circuit. An external clock signal from the MCU,
crystal, or ceramic resonator is configured with resistors and capacitors. To bias the inverter, a resistor (1 M
typ) is placed across XIN and XOUT.
This clock signal is prescaled to set the internal sampling frequency of the A/D converter.
oscillator output (XOUT)
The XOUT terminal is the output of the inverter used for the oscillator circuit.
data output (SDO)
The SDO output is the SPI data bus reporting information back to the microprocessor. This is a 3-state output
with the output set to high-impedance mode when CS is pulled to VDD. The high-impedance state can also be
programmed by setting a bit in the prescale word which takes precedence over the CS setting. The output is
disabled when the CS terminal is pulled high (VDD).
data input (SDI)
The SDI terminal is the communication interface for data transfer between the master and slave components.
The SDI has an internal pullup to VDD; the data stream is in 8-bit word format.
serial clock (SCLK)
The SCLK output signal is used for synchronous communication of data. Typically, the output from the master
clock is low with the IC having an internal pullup resistor to VDD. The data is clocked to the internal shift register
on the falling clock edge.
test (TEST)
The TEST terminal, when pulled low, allows the IC to enter the test mode. During normal operation, this terminal
is left open or tied high (VDD). There is an internal pullup to VDD (default).
feedback output for amplifiers (CH1FB and CH2FB)
The CHXFB are amplifier outputs for the sensor signals. The gain of the respective amplifiers is set using the
CHXFB and CHX input terminals (see Figure 1).
input amplifiers (CH1P, CH1N, CH2P, and CH2N)
CH1P, CH1N, CH2P, and CH2N are the inputs for the two amplifiers which interface to the external knock
sensors.
The gain is set by external resistors R1 and R2. The inputs and outputs of the amplifier are rail-to-rail compatible
to the supply VDD.
An internal multiplexer selects the desired sensor signal to process programmable through the SPI.
相關PDF資料 |
PDF描述 |
|---|---|
| TPIC8300IPWRQ1 | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| TPIC9201PWPR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| TPIC9201N | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDIP20 |
| TPL0102-100PWR | DIGITAL POTENTIOMETER, PDSO14 |
| TPL0102-100RUCR | DIGITAL POTENTIOMETER, PQCC14 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPIC8101EVM | 功能描述:EVALUATION MODULE 制造商:texas instruments 系列:* 零件狀態:在售 標準包裝:1 |
| TPIC82000 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Tire Pressure Monitoring System TX Module |
| TPIC8200041101FFER | 制造商:Texas Instruments 功能描述:LINEAR IC-NON VMI |
| TPIC82000FFE | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Tire Pressure Monitoring System TX Module |
| TPIC82000FFER | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Tire Pressure Monitoring System TX Module |
發布緊急采購，3分鐘左右您將得到回復。