- 您現在的位置：買賣IC網 > PDF目錄384026 > TPIC43T01 (Texas Instruments, Inc.) Three-Phase Brushless Motor RPM Controller PDF資料下載
參數資料
| 型號： | TPIC43T01 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | Three-Phase Brushless Motor RPM Controller |
| 中文描述： | 三相無刷電機 RPM 控制器 |
| 文件頁數： | 23/27頁 |
| 文件大?。?/td> | 376K |
| 代理商： | TPIC43T01 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁
TPIC43T01, TPIC43T02
THREE-PHASE BRUSHLESS MOTOR RPMCONTROLLERS
SLIS098 – APRIL 2000
23
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
PRINCIPLES OF OPERATION
EEPROM programming
Figure 18 presents the sequence of events required to program the onboard EEPROM. To begin the procedure,
the device must be placed into test mode by setting V
PP
to GND, TEST to V
DD
and V
CC
> 8 V. The SIENB input
must transition high to enable the serial input port (see Figure 19). Serial data is clocked into SI on the rising
edges of SCLK. Sixteen bits of data must be transferred during each serial transfer and SIENB must be set to
0 after the sixteenth clock. The first two bits transferred select the EEPROM address to be manipulated. Address
bit A0 is the least significant bit (LSB). The third bit sets the interface into read or write mode. A 1 selects a read
operation from the EEPROM and a 0 selects a write operation to the EEPROM. Set the next five unused bits
to 0. The next 8 bits of data are used for write operations, and are unused and should be set to zero for read
operations. The definition of the data word is presented in Table 7. SIENB must be set to 0 after the 16-bit transfer
has been completed. When new data is being programmed into the EEPROM, the V
PP
pin must transition to
13.5 V for at least 5 ms and then back to GND (see Figure 20). This completes the serial transfer and
programming sequence. Another transfer can begin using the same procedure. Only one register can be
programmed at a time. The TEST pin must be set to 0 after programming has been completed to disable the
serial test mode and reconfigure the multipurpose pins for normal operation.
Start
Set VPP = GND; Set TEST = VDD, VCC > 8 V
Set SIENB = H
Shift Address and Data into SI
Set SIENB = L
Ramp VPP to 13.5 V then back to GND
Figure 18. Recommended EEPROM Programming Sequence
相關PDF資料 |
PDF描述 |
|---|---|
| TPIC43T01DA | THREE-PHASE BRUSHLESS MOTOR RPM CONTROLLERS |
| TPS2010(中文) | Power Distribution Switch(過流、限流、欠壓鎖定、熱關閉及ESD保護,電源分配開關) |
| TPS2011(中文) | Power Distribution Switch(過流、限流、欠壓鎖定、熱關閉及ESD保護,電源分配開關) |
| TPS2012(中文) | Power Distribution Switch(過流、限流、欠壓鎖定、熱關閉及ESD保護,電源分配開關) |
| TPS2013(中文) | Power Distribution Switch(過流、限流、欠壓鎖定、熱關閉及ESD保護,電源分配開關) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPIC43T01DA | 功能描述:馬達/運動/點火控制器和驅動器 3 Phase Brushless MotorRPMController RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TPIC43T01DAR | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Brushless Motor RPM Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TPIC43T02 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:THREE-PHASE BRUSHLESS MOTOR RPM CONTROLLERS |
| TPIC43T02DA | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Brushless Motor RPM Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TPIC43T02DAR | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Brushless Motor RPM Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。