參數資料
型號： TPIC2101D
廠商： TEXAS INSTRUMENTS INC
元件分類： 運動控制電子
英文描述： BRUSH DC MOTOR CONTROLLER, 0.05 A, PDSO14
封裝： SOIC-14
文件頁數： 17/21頁
文件大小： 381K
代理商： TPIC2101D
TPIC2101
DC BRUSH MOTOR CONTROLLER
SLIS060 – OCTOBER 1995
5
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251–1443
current limit protection
Current through the motor is limited by lowering the GD terminal PWM when a high current situation occurs.
If the condition persists, the device shuts off the gate drive (GD terminal) until the circuit is reset externally by
entering the sleep state.
theory of operation
This section explains the normal circuit operation for the automatic and manual states.
power supply and oscillator
Positive voltage is supplied to the integrated circuit on the Vbat terminal, ground is the GND terminal. The IC
steps down the Vbat supply to the regulated 5.5 V supply at the V5P5 terminal. AREF is shorted to V5P5 in run
state and disconnected when the IC is in sleep state. Two terminal connections (COSC and ROSC) are provided
to control an internal oscillator. The oscillator freq, f(osc), is defined by the following equation:
f
(osc) +
2
ROSC
COSC
Nominal oscillator frequency is 20-kHz based on the recommended components.
automatic mode signal decoding
In automatic state, a high-to-low signal transition on the AUTO terminal (open collector) will wake the device
from the sleep state into the run state. The speed command information is contained in the duty cycle of a 100 Hz
PWM signal on the same terminal. The speed information is inverted, i.e. a signal that is 10% high commands
a faster speed than a 20% high signal. In automatic mode the MAN terminal is floating. The device is capable
of rejecting
± 2 V of ground offset VIO between the open-collector switching transistor and the GND terminal
without affecting the output duty cycle. Two terminals are provided for an RC integrator (SPEED and INT) to
average the incoming PWM signal for use as a PWM comparator input. Figure 2 illustrates the automatic state
connections.
2
3
499
499
No Connection
I = 100
A
VIO
20 k
min
27.4 k
14 2.75 V
4
7
4.7
F
MAN
AUTO
CCS
SPEED
INT
TPIC2101
Figure 2. Automatic Mode Connections
相關PDF資料
PDF描述
TPIC8101DW SPECIALTY CONSUMER CIRCUIT, PDSO20
TPIC8101DWR SPECIALTY CONSUMER CIRCUIT, PDSO20
TPIC8101DWG4 SPECIALTY CONSUMER CIRCUIT, PDSO20
TPIC8101DWRG4 SPECIALTY CONSUMER CIRCUIT, PDSO20
TPIC8300IPWRQ1 SPECIALTY ANALOG CIRCUIT, PDSO16
相關代理商/技術參數
參數描述
TPIC2101DG4 功能描述:馬達/運動/點火控制器和驅動器 Sgl Phase Lo-Side Pre-FET Drvr RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TPIC2101N 功能描述:馬達/運動/點火控制器和驅動器 Single Ph Low-Side Pre-FET Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
TPIC2202 制造商:TI 制造商全稱:Texas Instruments 功能描述:2-CHANNEL COMMON-SOURCE POWER DMOS ARRAY
TPIC2202KC 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Texas Instruments 功能描述:
TPIC2301 制造商:TI 制造商全稱:Texas Instruments 功能描述:3-CHANNEL COMMON-SOURCE POWER DMOS ARRAY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*