- 您現在的位置：買賣IC網 > PDF目錄385009 > TP3420AN (NATIONAL SEMICONDUCTOR CORP) ISDN S/T Interface Device PDF資料下載
參數資料
| 型號： | TP3420AN |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 數字傳輸電路 |
| 英文描述： | ISDN S/T Interface Device |
| 中文描述： | DATACOM, DIGITAL SLIC, PDIP20 |
| 封裝： | PLASTIC, DIP-20 |
| 文件頁數： | 16/32頁 |
| 文件大?。?/td> | 524K |
| 代理商： | TP3420AN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
Functional Description
(Continued)
3.
Contiguous B1+B2 (128 kbit/s) digital loopback (LBB1,
LBB2) in TEM mode and in NT/TES modes if FSa is
phase synchronous with FSb.
Contiguous B1+B2+D (144 kbit/s) digital loopback (LBD)
in TEM mode and in NT/TES modes if FSa is phase syn-
chronous with FSb.
B1 line loopback (using LBL1) with any FSa/FSb rela-
tionship in all TE or NT modes.
B2 line loopback (using LBL2) with any FSa/FSb rela-
tionship in all TE nor NT modes.
Contiguous B1+B2 (128 kbit/s pipe) line loopback
(LBL1, LBL2) with equal delay, available in TEM mode,
and in NT/TES modes if FSa is phase synchronous with
FSb.
Note that a line loopback for the D channel is not specified in
the CCITT I.430 or the T1-605 specification, to ensure that D
channel signaling is transparently passed end-to-end.
4.
5.
6.
7.
ACTIVATION/DEACTIVATION: TP3420A IN NT MODE
Activation (i.e. transmission and loop synchronization) may
be initiated from either end of the loop.
Activation initiated from the NT: to initiate Activation from the
NT, the TP3420A must be powered up, using a PUP com-
mand, followed (Note 12) by an AR instruction to the Control
Register. Network timing, i.e., an 8 kHz input to FS
, must be
present at this time. The device then begins to send data
framed as INFO 2 type, in which bits in the B, D and D-echo
channels are set to binary 0. These frames are detected by
the TE, which replies with data framed as INFO 3 type, syn-
chronized to received frames. A flywheel circuit in the
TP3420A NT searches for 3 consecutive correctly formatted
receive frames to acquire frame synchronization. If Multi-
framing is enabled (MIE), 60 correct frames (3 multiframes)
are required to achieve full loop synchronization. When it is
correctly in sync with received frames, the NT interrupts the
control processor with Status Indication type AP. A second
AR command is required to cause the NT to send INFO 4
frames, in which the B and D channels are enabled for trans-
mission; Status Indication type AI is then set, and the INT
output is pulled low to indicate Activation complete.
Note 12:
A delay of
≥
2 msecs is recommended to ensure that all internal cir-
cuits have settled.
Activation initiated by a TE: when Activation is initiated by a
TE, the TP3420A in NT mode will detect the incoming INFO
1 signal and, if it is powered-down will pull the LSD pin and
INT low, either of which can be used to “wake-up” a micro-
processor. A PUP command must then be written to
power-up the TP3420. Upon identifying the INFO 1 signal,
the device will set Status Indication type AP and pull INT low
to indicate that Activation is pending. No INFO 2 frames will
be transmitted until a Control instruction type AR is written to
the device, which allows the Activation sequence to proceed
as described above.
Once Activated, loss of frame alignment is assumed by the
TP3420A when a time which is equivalent to three frames
has passed without it detecting any of the valid pairs of line
code violations which obey the framing rule. If the NT does
detect alignment loss it will start to transmit INFO 2. At this
point the Error Indication (EI) primitive is set, the INT output
is pulled low and the receiver searches to identify the incom-
ing signal and attempt to re-acquire loop synchronization. If
it successfully re-establishes synchronization with the in-
coming signal (INFO 3 frames), a further interrupt is gener-
ated with Status Indication type AI and re-activation can be
completed by sending an AR command. If, however, the re-
ceiver subsequently identifies that the incoming line signal
has ceased, i.e. INFO 0 is being received, Status Indicator EI
is set and INT pulled low, with the transmitted frames
changed to INFO 2. Deactivation can then be completed by
a DR command, following which Status Indication type DI is
set and the INT output pulled low to indicate De-activation.
If required, a PDN instruction may be written to the Control
Register to power-down the device and enable the LSD out-
put.
I.430 recommends 2 timers should be available in an NT. An
Activation Request to the TP3420A should be associated
with the start of an external Timer 1, if required. Timer 1
should be stopped when the AI interrupt is generated follow-
ing successful Activation. If Timer 1 expires before AI is gen-
erated, however, Control Instruction type DR should be writ-
ten to the device to force de-activation. Timer 2, which is
specified to prevent unintentional reactivation, is not required
since the TP3420A can uniquely recognise INFO 1 frames.
ACTIVATION/DEACTIVATION: TP3420A IN TE MODE
Activation initiated by the TE: to activate the loop with the
TP3420A at the TE end the device must first be powered-up
by a PUP command, followed (Note 3) by a Control Instruc-
tion type AR, which is the Activation Request to begin trans-
mission of INFO 1 frames after verifying that INFO 0 is being
received from the NT. INFO 1 is a continuous pattern of 0+,
0, and 6 ‘1’s repeated. At this point the TE is running from
its local oscillator and is not receiving any sync information
from the NT. When the NT recognises this “wake-up” signal,
it begins to transmit INFO 2, synchronized to the network
clock (following activation of the “U” interface, if applicable).
This enables the phase-locked loop in the TE’s receiver to
correctly identify bit timing from the NT and to synchronize its
own transmission to that of the NT. On identifying INFO 2 for
3 consecutive frames, the TE changes its transmit data to
INFO 3 and awaits the return of INFO 4 from the NT. Identi-
fication of INFO 4 completes the Activation sequence, so
Status Indication type AI is set, and the INT output pulled
low.
Activation initiated from the NT: when Activation is initiated
by the NT, if the TP3420A in TE mode is powered down, it
will pull the LSD pin and INT low on receiving a line signal.
Either of these can be used to “wake-up” a microprocessor.
A PUP command is required to enable the device to
power-up, identify the received signal, and acquire bit and
frame synchronization. Once INFO 2 has been identified, the
TP3420Awill pull INT low, with Status Indication typeAP set,
to alert the microprocessor that Activation is pending. The
microprocessor must respond by writing Control Instruction
typeAR in order forActivation to proceed. INFO 3 frames are
then transmitted. Finally, an AI Status Indication interrupt is
generated when the NT replies with INFO 4 frames.
As in NT mode, once Activated, loss of frame alignment is
assumed by the TP3420A when a time equivalent to three
frames has passed without it detecting any of the valid pairs
of line code violations which obey the framing rule. If the TE
does detect alignment loss it will cease transmitting immedi-
ately. At this point the Error Indication (EI) primitive is set in
the Status Register, the INT output is pulled low and the re-
ceiver searches to re-acquire loop synchronization if INFO 2
or INFO 4 frames are still being received. If synchronization
is re-established, a further interrupt is generated, with Status
Indication type AI. If, however, the receiver subsequently
identifies that the incoming line signal has ceased, i.e. INFO
www.national.com
16
相關PDF資料 |
PDF描述 |
|---|---|
| TP3420AV | ISDN S/T Interface Device |
| TP3464 | MICROWIRE⑩ Interface Device (MID) |
| TP3464N | MICROWIRE⑩ Interface Device (MID) |
| TP3465N | MICROWIRE⑩ Interface Device (MID) |
| TP3465V | MICROWIRE⑩ Interface Device (MID) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TP3420AN308 | 功能描述:IC INTERFACE DEVICE ISDN 20-DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:* 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| TP3420AV | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:ISDN S/T Interface Device |
| TP3420AV308 | 功能描述:射頻收發器 RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| TP3420AV308/63 | 功能描述:射頻收發器 RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| TP3420AV308/63SN | 功能描述:射頻收發器 RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。