- 您現(xiàn)在的位置：買賣IC網 > PDF目錄385005 > TNY256P (POWER INTEGRATIONS INC) TinySwitch Plus Energy Efficient, Low Power Off-line Switcher PDF資料下載
參數資料
| 型號： | TNY256P |
| 廠商： | POWER INTEGRATIONS INC |
| 元件分類： | 穩(wěn)壓器 |
| 英文描述： | TinySwitch Plus Energy Efficient, Low Power Off-line Switcher |
| 中文描述： | SWITCHING CONTROLLER, PDIP8 |
| 封裝： | 0.300 INCH, PLASTIC, DIP-8 |
| 文件頁數： | 8/20頁 |
| 文件大?。?/td> | 509K |
| 代理商： | TNY256P |
C
7/01
TNY256
8
Figure 13. Recommended PC Layout for TinySwitch without Under-Voltage Lock Out Resistor.
Layout
Single Point Grounding
Use a single point ground connection at the SOURCE pin for the
BYPASS pin capacitor and the Input Filter Capacitor (see
Figure 13).
Primary Loop Area
The area of the primary loop that connects the input filter
capacitor, transformer primary and
TinySwitch
together, should
be kept as small as possible.
Primary Clamp Circuit
A clamp or snubber circuit is used to minimize peak voltage and
ringing on the DRAIN pin at turn-off. This can be achieved by
using an RC snubber for less than 3 W or an RCD clamp as
shown in Figure 13 for higher power. A Zener and diode clamp
across the primary or a single 550 V Zener clamp from DRAIN
to SOURCE can also be used. In all cases care should be taken
to minimize the circuit path from the snubber/clamp components
to the transformer and
TinySwitch
.
Thermal Considerations
Copper underneath the
TinySwitch
acts not only as a single point
ground, but also as a heatsink. The hatched area shown in
Figure13 should be maximized for good heat-sinking of
TinySwitch
and output diode.
EN/UV pin layout optimization
The EN/UV pin connection to the opto-coupler should be kept
to an absolute minimum (less than 0.5 in.), and this connection
should be kept away from the DRAIN pin (minimum of 0.2 in.).
These distance limitations are critical only in applications
where an external under-voltage resistor (2 M
) is not used.
Y-Capacitor
The placement of the Y-capacitor should be directly from the
primary single point ground to the common/return terminal on
the secondary side. Such placement will maximize the EMI
benefit of the Y-capacitor.
Optocoupler
It is important to maintain the minimum circuit path from the
optocoupler transistor to the
TinySwitch
EN/UV and SOURCE
pins to minimize noise coupling.
Output Diode
For best performance, the area of the loop connecting the
secondary winding, the Output Diode and the Output Filter
Capacitor, should be minimized. See Figure13 for optimized
layout. In addition, sufficient copper area should be provided
at the anode and cathode terminals of the diode to adequately
heatsink the diode under output short circuit conditions.
Input and Output Filter Capacitors
There are constrictions in the traces connected to the input and
output filter capacitors. These constrictions are present for two
reasons. The first is to force all the high frequency currents to
flow through the capacitor (if the trace were wide then it could
flow around the capacitor). Secondly, the constrictions minimize
the heat transferred from the
TinySwitch
to the input filter
capacitor and from the secondary diode to the output filter
capacitor. The common/return (the negative output terminal in
Figure13) terminal of the output filter capacitor should be
connected with a short, low resistance path to the secondary
winding. In addition, the common/return output connection
should be taken directly from the secondary winding pin and not
from the Y-capacitor connection point.
TOP VIEW
PI-2360-012199
Y1-
Capacitor
Opto-
coupler
C
BP
D
EN/UV
BP
TinySwitch
+
–
HV
+
–
DC
Out
Input Filter Capacitor
Output Filter Capacitor
Safety Spacing
Transformer
Maximize hatched copper
areas ( ) for optimum
heat sinking
S
S
PRI
SEC
相關PDF資料 |
PDF描述 |
|---|---|
| TNY256Y | TinySwitch Plus Energy Efficient, Low Power Off-line Switcher |
| TNY256 | CONNECTOR ACCESSORY |
| TNY264 | Enhanced, Energy Efficient, Low Power Off-line Switcher |
| TNY264G | Enhanced, Energy Efficient, Low Power Off-line Switcher |
| TNY264P | Enhanced, Energy Efficient, Low Power Off-line Switcher |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TNY256PN | 功能描述:交流/直流開關轉換器 10W 85-265 VAC 15W 100/115/230 VAC RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓（最大值）:23.5 V 輸入/電源電壓（最小值）:11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel |
| TNY256Y | 功能描述:交流/直流開關轉換器 11W 85-265 VAC 19W 100/115/230 VAC RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓（最大值）:23.5 V 輸入/電源電壓（最小值）:11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel |
| TNY256YN | 功能描述:交流/直流開關轉換器 11W 85-265 VAC 19W 100/115/230 VAC RoHS:否 制造商:STMicroelectronics 輸出電壓:800 V 輸入/電源電壓（最大值）:23.5 V 輸入/電源電壓（最小值）:11.5 V 開關頻率:115 kHz 電源電流:1.6 mA 工作溫度范圍:- 40 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SSO-10 封裝:Reel |
| TNY263 | 制造商:POWERINT 制造商全稱:Power Integrations, Inc. 功能描述:Enhanced, Energy Efficient, Low Power Off-line Switcher |
| TNY263_04 | 制造商:POWERINT 制造商全稱:Power Integrations, Inc. 功能描述:Enhanced, Energy Efficient, Low Power Off-line Switcher |
發(fā)布緊急采購，3分鐘左右您將得到回復。