- 您現在的位置：買賣IC網 > PDF目錄385001 > TMS28F010B-10 (Texas Instruments, Inc.) 131072 BY 8-BIT FLASH MEMORY PDF資料下載
參數資料
| 型號： | TMS28F010B-10 |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | 131072 BY 8-BIT FLASH MEMORY |
| 中文描述： | 131072 8位快閃記憶體 |
| 文件頁數： | 6/23頁 |
| 文件大?。?/td> | 332K |
| 代理商： | TMS28F010B-10 |
TMS28F010B
131072 BY 8-BIT
FLASH MEMORY
SMJS824B – MAY 1995 – REVISED AUGUST 1997
6
POST OFFICE BOX 1443
HOUSTON, TEXAS 77251–1443
operation
Modes of operation are shown in Table 1.
Table 1. Operation Modes
FUNCTION
MODE
VPP
(1)
VPPL
VPPL
VPPL
E
(22)
G
(24)
A0
(12)
A9
(26)
W
(31)
DQ0–DQ7
(13–15, 17–21)
Read
VIL
VIL
VIH
VIL
VIH
X
X
X
VIH
VIH
X
Data Out
Output Disable
X
X
Hi-Z
Read
Standby and Write Inhibit
X
X
Hi-Z
Algorithm Selection Mode
Algorithm-Selection Mode
VPPL
VIL
VIL
VIL
VIH
X
VID
VIH
Mfr Equivalent Code 89h
Device Equivalent Code B4h
Read
VPPH
VPPH
VPPH
VPPH
VIL
VIL
VIH
VIL
VIL
VIH
X
VIH
X
VIH
VIH
X
Data Out
Read/
Write
Output Disable
X
X
Hi-Z
Standby and Write Inhibit
Write
X can be VIL or VIH.
VPPL
≤
VCC + 2 V; VPPH is the programming voltage specified for the device. For more details, refer to the recommended operating conditions.
read/output disable
X
X
X
X
Hi-Z
Data In
VIL
When the outputs of two or more TMS28F010Bs are connected in parallel on the same bus, the output of any
particular device in the circuit can be read with no interference from the competing outputs of other devices. To
read the output of the TMS28F010B, a low-level signal is applied to the E and G pins. All other devices in the
circuit should have their outputs disabled by applying a high-level signal to one of these pins.
standby and write inhibit
Active I
CC
current can be reduced from 30 mA to 1 mA by applying a high TTL level on E or to 100
μ
A with a
high CMOS level on E. In this mode, all outputs are in the high-impedance state. The TMS28F010B draws active
current when it is deselected during programming, erasure, or program/erase verification. It continues to draw
active current until the operation is terminated.
algorithm-selection mode
The algorithm-selection mode provides access to a binary code identifying the correct programming and erase
algorithms. This mode is activated when A9 (pin 26) is forced to V
ID
. Two identifier bytes are accessed by
toggling A0. All other addresses must be held low. A0 low selects the manufacturer equivalent code 89h, and
A0 high selects the device equivalent code B4h, as shown in Table 2.
Table 2. Algorithm-Selection Modes
IDENTIFIER
§
PINS
A0
VIL
VIH
DQ7
1
DQ6
0
DQ5
0
DQ4
0
DQ3
1
DQ2
0
DQ1
0
DQ0
1
HEX
89
Manufacturer Equivalent Code
Device Equivalent Code
§E = G = VIL, A1–A8 = VIL, A9 = VID, A10–A16 = VIL, VPP = VPPL.
programming and erasure
1
0
1
1
0
1
0
0
B4
In the erased state, all bits are at a logic 1. Before erasing the device, all memory bits must be programmed to
a logic 0. Afterwards, the entire chip is erased. At this point, the bits, now logic 1s, can be programmed
accordingly. Refer to the Fastwrite and Fasterase algorithms for further detail.
相關PDF資料 |
PDF描述 |
|---|---|
| TMS28F010B-12 | 131072 BY 8-BIT FLASH MEMORY |
| TMS28F010B-15 | 131072 BY 8-BIT FLASH MEMORY |
| TMS28F010B-90 | 131072 BY 8-BIT FLASH MEMORY |
| TMS28F400BZ | 8-BIT/262144 BY 16-BIT BOOT-BLOCK FLASH MEMORIES |
| TMS28F400BZB80BDBJE | 8-BIT/262144 BY 16-BIT BOOT-BLOCK FLASH MEMORIES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMS28F010B-10C4DDE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| TMS28F010B-10C4DDE4 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| TMS28F010B-10C4DDL | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| TMS28F010B-10C4DDL4 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
| TMS28F010B-10C4DDQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Flash EEPROM |
發布緊急采購，3分鐘左右您將得到回復。