參數資料
型號: TMP86FS49BUG
元件分類: 微控制器/微處理器
英文描述: 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64
封裝: 10 X 10 MM, 0.50 MM PITCH, LEAD FREE, PLASTIC, LQFP-64
文件頁數: 24/54頁
文件大小: 2519K
代理商: TMP86FS49BUG
Page 13
TMP86FS49BUG
Note 1: In single clock mode, do not set DV7CK to “1”.
Note 2: Do not set “1” on DV7CK while the low-frequency clock is not operated stably.
Note 3: fc: High-frequency clock [Hz], fs: Low-frequency clock [Hz], *: Don’t care
Note 4: In SLOW1/2 and SLEEP1/2 modes, the DV7CK setting is ineffective, and fs is input to the 7th stage of the divider.
Note 5: When STOP mode is entered from NORMAL1/2 mode, the DV7CK setting is ineffective during the warm-up period after
release of STOP mode, and the 6th stage of the divider is input to the 7th stage during this period.
2.2.2.2 Machine cycle
Instruction execution and peripheral hardware operation are synchronized with the main system clock.
The minimum instruction execution unit is called an “machine cycle”. There are a total of 10 different
types of instructions for the TLCS-870/C Series: Ranging from 1-cycle instructions which require one
machine cycle for execution to 10-cycle instructions which require 10 machine cycles for execution. A
machine cycle consists of 4 states (S0 to S3), and each state consists of one main system clock.
Figure 2-5 Machine Cycle
2.2.3 Operation Mode Control Circuit
The operation mode control circuit starts and stops the oscillation circuits for the high-frequency and low-
frequency clocks, and switches the main system clock. There are three operating modes: Single clock mode,
dual clock mode and STOP mode. These modes are controlled by the system control registers (SYSCR1 and
SYSCR2). Figure 2-6 shows the operating mode transition diagram.
2.2.3.1 Single-clock mode
Only the oscillation circuit for the high-frequency clock is used, and P21 (XTIN) and P22 (XTOUT)
pins are used as input/output ports. The main-system clock is obtained from the high-frequency clock. In
the single-clock mode, the machine cycle time is 4/fc [s].
(1) NORMAL1 mode
In this mode, both the CPU core and on-chip peripherals operate using the high-frequency clock.
The TMP86FS49BUG is placed in this mode after reset.
Timing Generator Control Register
TBTCR
(0036H)
76
5
4
3
2
1
0
(DVOEN)
(DVOCK)
DV7CK
(TBTEN)
(TBTCK)
(Initial value: 0000 0000)
DV7CK
Selection of input to the 7th stage
of the divider
0: fc/28 [Hz]
1: fs
R/W
Main system clock
State
Machine cycle
S3
S2
S1
S0
S3
S2
S1
S0
1/fc or 1/fs [s]
相關PDF資料
PDF描述
TMP86PS25F 8-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP100
TMP87C800N 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDIP64
TMP89FH46LDUG 8-BIT, FLASH, MICROCONTROLLER, PQFP48
TMP89FM42UG 8-BIT, FLASH, 10 MHz, MICROCONTROLLER, PQFP44
TMPA8700CPF 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP44
相關代理商/技術參數
參數描述
TMP86FS49BUG(C,JZ) 功能描述:8位微控制器 -MCU INTEGRATED CIRCUIT MICROCONTROLLER - TLCS870C FAMILY RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
TMP86FS49FG 功能描述:IC MCU FLASH 8BIT 60K 64QFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:TLCS-870/C 標準包裝:160 系列:HCS12 核心處理器:HCS12 芯體尺寸:16-位 速度:25MHz 連通性:CAN,EBI/EMI,SCI,SPI 外圍設備:POR,PWM,WDT 輸入/輸出數:35 程序存儲器容量:128KB(128K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:4K x 8 電壓 - 電源 (Vcc/Vdd):2.35 V ~ 5.5 V 數據轉換器:A/D 8x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:52-LQFP 包裝:托盤
TMP86FS64FG 制造商:Toshiba America Electronic Components 功能描述:MCU 8BIT TLCS-870 CISC 60KB FLASH 5V 100PQFP - Bulk
TMP86FS64FG(TZ) 功能描述:8位微控制器 -MCU 60K Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
TMP86P202MG 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:8 Bit Microcontroller