- 您現在的位置：買賣IC網 > PDF目錄98266 > TMDS461PZTR (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | TMDS461PZTR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 封裝： | PLASTIC, TQFP-100 |
| 文件頁數： | 22/43頁 |
| 文件大?。?/td> | 3111K |
| 代理商： | TMDS461PZTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
TSCL
TSDA
9thClockPulse- AcknowledgeFromSlave
V
OL
OfSlave
V
OL
OfDriver T
I
2C Pullup Resistors
www.ti.com ............................................................................................................................................................................................... SLLS915 – JANUARY 2009
Figure 36 illustrates the waveforms seen on the T-side I2C-bus under the same operation as in Figure 35. On the
T-side of the I2C repeater, the clock and data lines would have a positive offset from ground equal to the VOL of
the driver T. After the 8th clock pulse, the data line is pulled to the VOL of the slave device, which is very close to
ground in this example. At the end of the acknowledge, the slave device releases and the bus level rises back to
the VOL set by the driver until the R-side rises above VCC/2, after which it continues to be high. It is important to
note that any arbitration or clock-stretching events require that the low level on the T-side bus at the input of the
TMDS461 I2C repeater is below 0.4 V to be recognized by the device and then transmitted to the R-side I2C bus.
Figure 36. Bus T Waveform
The pullup resistor value is determined by two requirements:
1. The maximum sink current of the I2C buffer is 3 mA or slightly higher for an I2C driver supporting
standard-mode I2C operation.
Rup(min) = VDD/Isink
(1)
2. The maximum transition time, T, of an I2C on the bus is set by an RC time constant, where R is the pullup
resistor value and C is the total load capacitance. The parameter, k, can be calculated from Equation 3 by
solving for t, the times at which certain voltage thresholds are reached. Different input threshold
combinations introduce different values of t. Table 3 summarizes the possible values of k under different
threshold combinations.
T = k × RC
(2)
V(t) = VDD(1 – e
–t/RC)
(3)
Table 3. Value of k for Different Input Threshold Voltages
Vth–\Vth+
0.7 VDD
0.65 VDD
0.6 VDD
0.55 VDD
0.5 VDD
0.45 VDD
0.4 VDD
0.35 VDD
0.3 VDD
0.1 VDD
1.0986
0.9445
0.8109
0.6931
0.5878
0.4925
0.4055
0.3254
0.2513
0.15 VDD
1.0415
0.8873
0.7538
0.6360
0.5306
0.4353
0.3483
0.2683
0.1942
0.2 VDD
0.9808
0.8267
0.6931
0.5754
0.4700
0.3747
0.2877
0.2076
0.1335
0.25 VDD
0.9163
0.7621
0.6286
0.5108
0.4055
0.3102
0.2231
0.1431
0.0690
0.3 VDD
0.8473
0.6931
0.5596
0.4418
0.3365
0.2412
0.1542
0.0741
—
From Equation 1, Rup(min) = 5.5 V/3 mA = 1.83 k to operate the bus under a 5-V pullup voltage and provide less
than 3 mA when the I2C device is driving the bus to a low state. If a higher sink current, for example 4 mA, is
allowed, Rup(min) can be as low as 1.375 k.
Given a 5-V I2C device with input low and high threshold voltages at 0.3 Vdd and 0.7 Vdd, respectively, the value
of k is 0.8473 from Table 3. Taking into account the 1.83-k
pullup resistor, the maximum total load capacitance
is C(total-5V) = 645 pF. Ccable(max) should be restricted to be less than 545 pF if Csource and CI can be as high as 50
pF. Here the CI is treated as Csink, the load capacitance of a sink device.
Fixing the maximum transition time from Table 3, T = 1
s, and using the k values from Table 3, the
recommended maximum total resistance of the pullup resistors on an I2C bus can be calculated for different
system setups.
To support the maximum load capacitance specified in the HDMI spec, Ccable(max) = 700 pF/Csource = 50 pF/CI =
Copyright 2009, Texas Instruments Incorporated
29
Product Folder Link(s) :TMDS461
相關PDF資料 |
PDF描述 |
|---|---|
| TMP431BDGKT | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| TMP435ADGST | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| TMS320AV100PBM | SPECIALTY CONSUMER CIRCUIT, PQFP120 |
| TMS320AV120FN | SPECIALTY CONSUMER CIRCUIT, PQCC44 |
| TMS320AV220PCM | SPECIALTY CONSUMER CIRCUIT, PQFP144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TMDS570LS12HDK | 功能描述:TMS570LS Hercules? MCU 32-Bit ARM? Cortex?-R4F Embedded Evaluation Board 制造商:texas instruments 系列:Hercules? 零件狀態:有效 板類型:評估平臺 類型:MCU 32-位 核心處理器:ARM? Cortex?-R4F 操作系統:- 平臺:- 配套使用產品/相關產品:TMS570LS 安裝類型:固定 內容:板，電纜，配件 標準包裝:1 |
| TMDS570LS31HDK | 制造商:Texas Instruments 功能描述:HERCULES DEVELOPMENT KIT |
| TMDS570LS31USB | 功能描述:EVAL BOARD HERCULES 制造商:texas instruments 系列:Hercules? 零件狀態:停產 板類型:評估平臺 類型:MCU 32-位 核心處理器:ARM? Cortex?-R4F 操作系統:- 平臺:- 配套使用產品/相關產品:TMS570LS 安裝類型:固定 內容:板，電纜，配件 標準包裝:1 |
| TMDS9P701014 | 制造商:Texas Instruments 功能描述: |
| TMDSACDCKIT | 功能描述:開發板和工具包 - TMS320 C2000 AC/DC Dev Kit RoHS:否 制造商:Texas Instruments 產品:Experimenter Kits 工具用于評估:F2802x 核心:TMS320 接口類型:UART, USB 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。