- 您現在的位置：買賣IC網 > PDF目錄385933 > TLV1570EVM (Texas Instruments, Inc.) TLV1570 Evaluation Module(TLV1570評估板) PDF資料下載
參數資料
| 型號： | TLV1570EVM |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | TLV1570 Evaluation Module(TLV1570評估板) |
| 中文描述： | TLV1570評估模塊（TLV1570評估板） |
| 文件頁數： | 14/34頁 |
| 文件大?。?/td> | 226K |
| 代理商： | TLV1570EVM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
Onboard Signal Conditioning
2-4
Analog Configuration
2.3
Onboard Signal Conditioning
The multiplexer output of the TLV1570 is not directly connected to the input of
the converter. That makes it possible to insert a signal-conditioning circuit
between the multiplexer and the ADC. On the EVM, an amplifier [TLV2231
(U4)] can be inserted in the signal path (determined by JP3 and JP4). The
default gain of the amplifier is 1.0, but can be changed with R3 and R4 (as
shown in the following equation).
G
1
R3
R4
The SMA terminal can be used to connect the output of a function generator
directly to the input of the ADC. It is possible to set the input impedance to the
required value (R19). However, if the signal is routed via the multiplexer, R19
should be left open to avoid errors due to the current through this resistor.
Jumper
Default
Description
JP3, JP4
Both RIGHT
Amplifier between multiplexer and ADC
Both LEFT
Multiplexer connected directly to ADC
2.4
Eight-Channel Direct Operation
In this mode, all eight channels of the ADC are accessible via J1. For this, both
JP1 and JP2 must be switched to the following positions:
JP1
JP2
UP
DOWN
2.5
Variable dc Voltage on Channel 7
To test the basic function of the ADC, the potentiometer R2 provides a dc
voltage between 0 V and the reference voltage. JP1 connects the wiper of the
potentiometer to channel 7.
JP1
DOWN
2.6
Loopback Mode on Channel 0
The onboard DAC (TLV5616) is used to run the board in a loopback mode. The
voltage, generated by the DAC, is connected to channel 0 with JP2.
JP2
UP
相關PDF資料 |
PDF描述 |
|---|---|
| TLV1571(中文) | 2.7V to 5.5V, 1-Channel, 10-Bit, Parallel Analog-to-Digital Converters(2.7V-5.5V,10位,1.25MSPS,單通道,低功耗,自動掉電的并行ADC) |
| TLV1578(中文) | 2.7V to 5.5V, 8-Channel, 10-Bit, Parallel Analog-to-Digital Converters(2.7V-5.5V,10位,1.25MSPS,八通道,低功耗,自動掉電的并行ADC) |
| TLV1571EVM | TLV1571 Evaluation Module(TLV1571評估板) |
| TLV1572(中文) | High-Speed 10-Bit Successive-Approximation Analog-To-Digital Converter (ADC)(2.7V至5.5V,10位,1.25MSPS帶自動關機的串行A/D轉換器) |
| TLV2211(中文) | Single LINCMOS Rail-To-Rail Micropower OP AMP(先進的LinCMOS滿電源幅度微功率運算放大器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLV1570IDW | 功能描述:模數轉換器 - ADC 10bit 1.25MSPS Ser RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLV1570IDWG4 | 功能描述:模數轉換器 - ADC 10-Bit 1.25 MSPS 8-Ch DSP RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLV1570IDWR | 制造商:Texas Instruments 功能描述: |
| TLV1570IPW | 功能描述:模數轉換器 - ADC 10bit 1.25MSPS Ser RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TLV1570IPWG4 | 功能描述:模數轉換器 - ADC 10-Bit 1.25 MSPS 8-Ch DSP RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。