- 您現在的位置：買賣IC網 > PDF目錄383955 > TLE6288R (INFINEON TECHNOLOGIES AG) Smart 6 Channel Peak&Hold Switch PDF資料下載
參數資料
| 型號： | TLE6288R |
| 廠商： | INFINEON TECHNOLOGIES AG |
| 英文描述： | Smart 6 Channel Peak&Hold Switch |
| 中文描述： | 智能6通道峰 |
| 文件頁數： | 15/23頁 |
| 文件大?。?/td> | 1258K |
| 代理商： | TLE6288R |
Preliminary Datasheet TLE6288 R
Vp2
Page 15
13.01.2003
8.2
SPI Diagnostics:
As soon as a fault occurs for longer than the fault filtering time, the fault information is latched into the
diagnosis register (and the Fault pin will change from high to low state). A new error on the same
channel will over-write the old error report. Serial data out pin (SO) is in a high impedance state when
CS
is high. If
CS
receives a LOW signal, all diagnosis bits can be shifted out serially. If the sent com-
mand was valid the rising edge of
CS
will reset the diagnosis registers (except the channel OT flag)
and restart the fault filtering time. In case of an invalid command the device will ignore the data bits and
the diagnosis register will not be reset at the rising
CS
edge.
Figure 1: Two bits per channel diagnostic feedback plus two overtemperature flags
For Full Diagnosis there are two diagnostic bits per channel configured as shown in Figure 1.
Diagnosis bit0 and bit1 are always set to 1.
Normal function:
The bit combination
HH
indicates that there is no fault condition, i.e. normal function.
Overload, Shorted Load or Overtemperature:
HL
is set when the current limitation gets active, i.e.
there is a overload, short to supply or overtemperature condition. The second reason for this bit combi-
nation is overtemperature of the corresponding channel.
Open load: LH
is set when open load is detected (in off state of the channel)
Switch Bypassed:
Short to GND :
in lowside configuration LL is set when this condition is detected
Short to Battery :
in highside configuration LL is set when this condition is detected
Channel Overtemperature Flag:
In case of overtemperature in any output channel in on state the
overtemperature Flag in the SPI diagnosis register is set (change bit 3 from 0 to 1). This Bit can be
used to distinguish between Overload and Overtemperature (both HL combination) and is reset by
switching OFF/ON the affected channel.
In addition the DIAG6 / Ovtertemp pin is set low (if configured as Overtemp.Flag).
IC Overtemperature Flag:
When the IC logic tremperature exceeds typ.170° the non-latching IC
Overtemperature Flag will be set in the SPI diagnosis register(change bit 2 from 0 to 1).
In addition the DIAG6 / Ovtertemp pin is set low (if configured as Overtemp.Flag).
8.3
SPI Commands, Values and Parameters:
Diagnostic Serial Data Out SO
HH
HL
LH
LL
Normal function
Overload, Shorted Load or Overtemperature
Open Load
Switch Bypassed
Ch.6
Ch.5
Ch.4
Ch.3
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MSB
Ch.2
Ch.1
LSB
Channel Overtem-
perature Flag
IC Overtem-
perature Flag
Bit0 and Bit1
is always 1
相關PDF資料 |
PDF描述 |
|---|---|
| TLE6363 | Multifunctional Voltage Regulator and Watchdog |
| TLE6363G | Multifunctional Voltage Regulator and Watchdog |
| TLE6365G | Step Down Voltage-Regulator with Reset |
| TLK1101ERGPT | 11.3-Gbps Cable and PC Board Equalizer |
| TLK1221RHA | ETHERNET TRANSCEIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TLE6288R_10 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:Smart 6 Channel Peak & Hold Switch |
| TLE6288RAUMA2 | 制造商:Infineon Technologies AG 功能描述:IC SW SMART MULTICHAN PDSO36 |
| TLE6288RNT | 制造商:Infineon Technologies AG 功能描述:Power Switch Hi Side/Lo Side 36-Pin DSO |
| TLE6288RXT | 功能描述:電源開關 IC - 配電 Smart 6 Ch Peak/Hold Switch 4.5-5.5V RoHS:否 制造商:Exar 輸出端數量:1 開啟電阻（最大值）:85 mOhms 開啟時間（最大值）:400 us 關閉時間（最大值）:20 us 工作電源電壓:3.2 V to 6.5 V 電源電流（最大值）: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-23-5 |
| TLE6289GP | 功能描述:功率驅動器IC DRIVER ICS RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。