- 您現在的位置：買賣IC網 > PDF目錄385927 > TK2150 (Electronic Theatre Controls, Inc.) STEREO 200W CLASS-T DIGITAL AUDIO AMPLIFIER DRIVER USING DIGITAL POWER PROCESSING TECHNOLOGY PDF資料下載
參數資料
| 型號： | TK2150 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEREO 200W CLASS-T DIGITAL AUDIO AMPLIFIER DRIVER USING DIGITAL POWER PROCESSING TECHNOLOGY |
| 中文描述： | 類立體聲功率200W - T的數字音頻放大器驅動程序使用數字功率處理技術 |
| 文件頁數： | 10/34頁 |
| 文件大?。?/td> | 663K |
| 代理商： | TK2150 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁
Tripath Technology, Inc. - Technical Information
10
TK2150 – Rev. 1.0/12.02
External Components Description
(Refer to the Application/Test Circuit)
Components Description
R
I
Inverting input resistance to provide AC gain in conjunction with R
F
. This input is
biased at the BIASCAP voltage (approximately 2.5VDC).
R
F
Feedback resistor to set AC gain in conjunction with R
I
. Please refer to the Amplifier
Gain paragraph, in the Application Information section.
C
I
AC input coupling capacitor which, in conjunction with R
I
, forms a highpass filter at
)
C
R
2
(
1
f
I
I
C
π
=
.
R
FBA
Feedback divider resistor connected to V5. This resistor is normally set at 1k
.
R
FBB
Feedback divider resistor connected to AGND. This value of this resistor depends
on the supply voltage setting and helps set the TK2150 gain in conjunction with R
I,
R
F,
R
FBA,
and R
FBC
. Please see the Modulator Feedback Design paragraphs in the
Application Information Section.
R
FBC
Feedback resistor connected from either the OUT1(OUT2) to FBKOUT1(FBKOUT2)
or speaker ground to FBKGND1(FBKGND2). The value of this resistor depends on
the supply voltage setting and helps set the TK2150 gain in conjunction with R
I,
R
F,
R
FBA,
, and R
FBB
. It should be noted that the resistor from OUT1(OUT2) to
FBKOUT1(FBKOUT2) must have a power rating of greater than
Please see the Modulator Feedback Design paragraphs in the Application
Information Section.
C
FB
Feedback delay capacitor that both lowers the idle switching frequency and filters
very high frequency noise from the feedback signal, which improves amplifier
performance. The value of C
FB
should be offset between channel 1 and channel 2
so that the idle switching difference is greater than 40kHz. Please refer to the
Application / Test Circuit.
R
OFA
Potentiometer used to manually trim the DC offset on the output of the TK2350.
R
OFB
Resistor that limits the manual DC offset trim range and allows for more precise
adjustment.
R
REF
Bias resistor. Locate close to pin 15 of the TC2001 and ground at pin 20 of the
TC2001.
C
A
BIASCAP decoupling capacitor. Should be located close to pin 1 of the TC2001 and
grounded at pin 20 of the TC2001.
D
B
Bootstrap diode. This diode charges up the bootstrap capacitors when the output is
low (at VNN) to drive the high side gate circuitry. A fast or ultra fast recovery diode
is recommended for the bootstrap circuitry. In addition, the bootstrap diode must be
able to sustain the entire VPP-VNN voltage. Thus, for most applications, a 150V (or
greater) diode should be used.
C
B
High frequency bootstrap capacitor, which filters the high side gate drive supply.
This capacitor must be located as close to VBOOT1 (pin 57 of the TP2150) or
VBOOT2 (pin 27 of the TP2150) for reliable operation. The “negative” side of C
B
should be connected directly to the HO1COM (pin 47 of the TP2150) or HO2COM
(pin 37 of the TP2150). Please refer to the Application / Test Circuit.
C
BAUX
Bulk bootstrap capacitor that supplements C
B
during “clipping” events, which result
in a reduction in the average switching frequency.
R
B
Bootstrap resistor that limits C
BAUX
charging current during TK2150 power up
(bootstrap supply charging).
C
S
Supply decoupling for the power supply pins. For optimum performance, these
components should be located close to the TC2001 and TP2150 and returned to
their respective ground as shown in the Application/Test Circuit.
R
VNN1
Main overvoltage and undervoltage sense resistor for the negative supply (VNN).
Please refer to the Electrical Characteristics Section for the trip points as well as the
hysteresis band. Also, please refer to the Over / Under-voltage Protection section in
the Application Information for a detailed discussion of the internal circuit operation
and external component selection.
R
VNN2
Secondary overvoltage and undervoltage sense resistor for the negative supply
(VNN). This resistor accounts for the internal V
NNSENSE
bias of 1.25V. Nominal
)
(2R
VPP
P
FBC
2
DISS
=
.
相關PDF資料 |
PDF描述 |
|---|---|
| TL-SCS1285 | Fixed-Voltage Regulator For SCSI Termination(用于SCSI 活動終端的低壓差固定電壓輸出穩壓器) |
| TL022C | DUAL LOW-POWER OPERATIONAL AMPLIFIERS |
| TL022M | DUAL LOW-POWER OPERATIONAL AMPLIFIERS |
| TL022MJG | DUAL LOW-POWER OPERATIONAL AMPLIFIERS |
| TL022MU | DUAL LOW-POWER OPERATIONAL AMPLIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TK2151 | 功能描述:折皺器 COAX KIT RoHS:否 制造商:Hirose Connector 類型: 描述/功能:Cable and Shield Crimper |
| TK215SC | 制造商:Thomas Betts 功能描述:Exact Equal/ 1-5 Days |
| TK215-SC-1 | 制造商:Thomas & Betts 功能描述:1 1/2 COUPLING,COMP.,EMT,DC,EA |
| TK2165 | 功能描述:折皺器 COAX KIT RoHS:否 制造商:Hirose Connector 類型: 描述/功能:Cable and Shield Crimper |
| TK216SC | 制造商:Thomas Betts 功能描述:Exact Equal/ 1-5 Days |
發布緊急采購，3分鐘左右您將得到回復。