- 您現在的位置：買賣IC網 > PDF目錄384975 > THS7316_07 (Texas Instruments, Inc.) 3-Channel HDTV Video Amplifier With 5th-Order Filters and 6-dB Gain PDF資料下載
參數資料
| 型號： | THS7316_07 |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | 3-Channel HDTV Video Amplifier With 5th-Order Filters and 6-dB Gain |
| 中文描述： | 3通道HDTV視頻放大器，具有5階濾波器和6 dB增益 |
| 文件頁數： | 15/30頁 |
| 文件大?。?/td> | 666K |
| 代理商： | THS7316_07 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
www.ti.com
INPUT MODE OF OPERATION – AC BIAS
Sync tip clamps work well for signals that have horizontal and/or vertical syncs associated with them. But, some
video signals do not have a sync embedded within the signal – such as Chroma or the P’
B
and P’
R
channels of a
480i/480p/576i/576p signal; or the bottom of the sync is not the lowest possible level of the video signal – such
as the P’
and P’
channels of a 720p and 1080i signal. If ac-coupling of these signals is desired, then a dc bias
is required to properly set the dc operating point within the THS7316. This function is easily accomplished with
the THS7316 by adding an external pull-up resistor to the positive power supply as shown in
Figure 30
.
THS7316
SLOS521–MARCH 2007
APPLICATION INFORMATION (continued)
When the AC Sync-Tip-Clamp (STC) operation is used, there must also be some finite amount of discharge bias
current. As previously described, if the input signal goes below the 0-V clamp level, the internal loop of the
THS7316 will source current to increase the voltage appearing at the input pin. As the difference between the
signal
level
and
the
0-V
reference
level
increases,
proportionally—supplying up to 3-mA of current. Thus the time to re-establish the proper STC voltage can be
fast. If the difference is small, then the source current is also small to account for minor voltage droop.
the
amount
of
source
current
increases
But, what happens if the input signal goes above the 0-V input level The problem is the video signal is always
above this level, and must not be altered in any way. But if the Sync level of the input signal is above this 0-V
level, then the internal discharge (sink) current will discharge the ac-coupled bias signal to the proper 0-V level.
This discharge current must not be large enough to alter the video signal appreciably, or picture quality issues
may arise. This is often seen by looking at the tilt (aka droop) of a constant luma signal being applied and
looking at the resulting output level. The associated change in luma level from the beginning of the video line to
the end of the video line is the amount of line tilt (droop).
If the discharge current is small, the amount of tilt is low which is good. But, the amount of time for the system to
capture the sync signal could be too long. This is also termed hum rejection. Hum arises from the ac line voltage
frequency of 50-Hz or 60-Hz. The value of the discharge current and the ac-coupling capacitor combine to
dictate the hum rejection and the amount of line tilt.
To allow for both dc-coupling and ac-coupling in the same part, the THS7316 incorporates an 800-k
resistor to
ground. Although a true constant current sink is preferred over a resistor, there are significant issues when the
voltage is near ground. This can cause the current sink transistor to saturate and cause potential problems with
the signal. This resistor is large enough as to not impact a dc-coupled DAC termination. For discharging an
ac-coupled source, Ohm’s Law is used. If the video signal is 1 V, then there is 1 V / 800 k
= 1.25-
μ
A of
discharge current. If more hum rejection is desired or there is a loss of sync occurring, then decrease the 0.1-
μ
F
input coupling capacitor. A decrease from 0.1
μ
F to 0.047
μ
F increases the hum rejection by a factor of 2.1.
Alternatively an external pull-down resistor to ground may be added which decreases the overall resistance, and
ultimately increases the discharge current.
To ensure proper stability of the AC STC control loop, the source impedance must be less than 1-k
with the
input capacitor in place. Otherwise, there is a possibility of the control loop to ring and this ringing may appear
on the output of the THS7316. Because most DACs or encoders use resistors to establish the voltage, which
are typically less than 300-
, then meeting the <1-k
requirement is done. But, if the source impedance looking
from the THS7316 input perspective is high, then add a 1-k
resistor to GND to ensure proper operation of the
THS7316.
15
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| THS7318_07 | 3-Channel Low-Power EDTV/SDTV Video Line Driver With Low-Pass Filters |
| THS9001DBVR | 50 MHz to 350 MHz CASCADEABLE AMPLIFIER |
| TI380PCM | PCI BUS INTERFACE FOR THE TI380 COMMPROCESSORS |
| TIBPAL22V10-20MFK | Adjustable 2.5-36V +/-0.4% Tolerance, 1-100mA Shunt Regulator; Package: SOIC-8 Narrow Body; No of Pins: 8; Container: Rail; Qty per Container: 98 |
| TIBPAL22V10-20MJT | HIGH-PERFORMANCE IMPACT-X E PROGRAMMABLE ARRAY LOGIC CIRCUITS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS7316D | 功能描述:視頻放大器 3-Ch HDTV Video Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| THS7316DG4 | 功能描述:視頻放大器 3-Ch HDTV Video Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| THS7316DR | 功能描述:視頻放大器 3-Ch HDTV Video Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| THS7316DRG4 | 功能描述:視頻放大器 3-Ch HDTV Video Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| THS7316EVM | 功能描述:放大器 IC 開發工具 THS7316 Eval Mod RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
發布緊急采購，3分鐘左右您將得到回復。