- 您現在的位置：買賣IC網 > PDF目錄384975 > THS7316_07 (Texas Instruments, Inc.) 3-Channel HDTV Video Amplifier With 5th-Order Filters and 6-dB Gain PDF資料下載
參數資料
| 型號： | THS7316_07 |
| 廠商： | Texas Instruments, Inc. |
| 元件分類： | 運動控制電子 |
| 英文描述： | 3-Channel HDTV Video Amplifier With 5th-Order Filters and 6-dB Gain |
| 中文描述： | 3通道HDTV視頻放大器，具有5階濾波器和6 dB增益 |
| 文件頁數： | 14/30頁 |
| 文件大小： | 666K |
| 代理商： | THS7316_07 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
www.ti.com
INPUT MODE OF OPERATION – AC SYNC TIP CLAMP
Some video DACs or encoders are not referenced to ground but rather to the positive power supply. These
DACs typically only sink current rather than the more traditional current sourcing DAC where the resistor is
referenced to ground. The resulting video signals can be too high of a voltage for a dc-coupled video buffer to
function properly. To account for this scenario the THS7316 incorporates a sync-tip clamp circuit. This function
requires a capacitor (nominally 0.1
μ
F) to be in series with the input. Note that while the term sync-tip-clamp is
used throughout this document, it should be noted that the THS7316 is be better termed as a dc-restoration
circuit based on how this function is performed. This circuit is an active clamp circuit and not a passive diode
clamp function.
+
-
+
-
+Vs
STC LPF
Comparator
Input
Pin
Input
Internal
Circuitry
800 k
W
0.1 F
m
+Vs
140 mV Level
Shifter
THS7316
SLOS521–MARCH 2007
APPLICATION INFORMATION (continued)
The input to the THS7316 has an internal control loop which sets the lowest input applied voltage to clamp at
ground (0-V). By setting the reference at 0-V, the THS7316 allows a dc-coupled input to also function. Hence,
the STC is considered transparent since it does not operate unless the input signal goes below ground. The
signal then goes through the same 140-mV level shifter resulting in an output voltage low level of 280-mV. If the
input signal tries to go below the 0-V, the internal control loop of the THS7316 will source up to 3-mA of current
to increase the input voltage level on the THS7316 input side of the coupling capacitor. As soon as the voltage
goes above the 0-V level, the loop stops sourcing current and becomes high impedance.
One of the concerns about the sync-tip-clamp level is how the clamp reacts to a sync edge that has
overshoot—common in VCR signals or reflections found in poor PCB layouts. Ideally the STC should not react
to the overshoot voltage of the input signal. Otherwise, this could result in clipping on the rest of the video signal
as it may raise the bias voltage too much.
To help minimize this input signal overshoot problem, the control loop in the THS7316 has an internal low-pass
filter as shown in
Figure 29
. This filter reduces the response time of the STC circuit. This delay is a function of
how far the voltage is below ground, but in general it is about a 80-ns delay. The effect of this filter is to slow
down the response of the control loop so as not to clamp on the input overshoot voltage, but rather the flat
portion of the sync signal.
As a result of this delay, the sync may have an apparent voltage shift. The amount of shift is dependant upon
the amount of droop in the signal as dictated by the input capacitor and the STC current flow. Because the sync
is primarily for timing purposes with syncing occurring on the edge of the sync signal, this shift is transparent in
most systems.
While this feature may not fully eliminate overshoot issues on the input signal for excessive overshoot and/or
ringing, the STC system should help minimize improper clamping levels. As an additional method to help
minimize this issue, an external capacitor (ex: 10 pF to 47 pF) to ground in parallel with the external termination
resistors can help filter overshoot problems.
It should be noted that this STC system is dynamic and does not rely upon timing in any way. It only depends on
the voltage appearing at the input pin at any given point in time. The STC filtering helps minimize level shift
problems associated with switching noises or very short spikes on the signal line. This helps ensure a very
robust STC system.
Figure 29. Equivalent AC Sync Tip Clamp Input Circuit
14
Submit Documentation Feedback
相關PDF資料 |
PDF描述 |
|---|---|
| THS7318_07 | 3-Channel Low-Power EDTV/SDTV Video Line Driver With Low-Pass Filters |
| THS9001DBVR | 50 MHz to 350 MHz CASCADEABLE AMPLIFIER |
| TI380PCM | PCI BUS INTERFACE FOR THE TI380 COMMPROCESSORS |
| TIBPAL22V10-20MFK | Adjustable 2.5-36V +/-0.4% Tolerance, 1-100mA Shunt Regulator; Package: SOIC-8 Narrow Body; No of Pins: 8; Container: Rail; Qty per Container: 98 |
| TIBPAL22V10-20MJT | HIGH-PERFORMANCE IMPACT-X E PROGRAMMABLE ARRAY LOGIC CIRCUITS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS7316D | 功能描述:視頻放大器 3-Ch HDTV Video Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| THS7316DG4 | 功能描述:視頻放大器 3-Ch HDTV Video Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| THS7316DR | 功能描述:視頻放大器 3-Ch HDTV Video Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| THS7316DRG4 | 功能描述:視頻放大器 3-Ch HDTV Video Amp RoHS:否 制造商:ON Semiconductor 通道數量:4 電源類型: 工作電源電壓:3.3 V, 5 V 電源電流: 最小工作溫度: 最大工作溫度: 封裝 / 箱體:TSSOP-14 封裝:Reel |
| THS7316EVM | 功能描述:放大器 IC 開發工具 THS7316 Eval Mod RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V |
發布緊急采購，3分鐘左右您將得到回復。