參數資料
型號： THS6043CD
廠商： Texas Instruments, Inc.
英文描述： 350 mA, 【12 V ADSL CPE LINE DRIVERS
中文描述： 350毫安，【12伏ADSL終端線路驅動器
文件頁數： 19/33頁
文件大小： 509K
代理商： THS6043CD
THS6042, THS6043
350 mA,
±
12 V ADSL CPE LINE DRIVERS
SLOS264G
–
MARCH 2000
–
REVISED DECEMBER 2001
19
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
APPLICATION INFORMATION
noise calculations and noise figure
Noise can cause errors on very small signals. This is especially true for the amplifying small signals. The noise
model for current feedback amplifiers (CFB) is the same as voltage feedback amplifiers (VFB). The only
difference between the two is that the CFB amplifiers generally specify different current noise parameters for
each input, while VFB amplifiers usually only specify one noise current parameter. The noise model is shown
in Figure 38. This model includes all of the noise sources as follows:
e
n
= Amplifier internal voltage noise (nV/
√
Hz)
IN+ = Noninverting current noise (pA/
√
Hz)
IN
–
= Inverting current noise (pA/
√
Hz)
e
Rx
= Thermal voltage noise associated with each resistor (e
Rx
= 4 kTR
x
)
_
+
RF
RS
RG
eRg
eRf
eRs
en
IN+
Noiseless
IN
–
eni
eno
Figure 38. Noise Model
The total equivalent input noise density (e
ni
) is calculated by using the following equation:
eni
en
2
IN
RS
2
IN
–
RF
RG
2
4 kTRs
4 kT RF
RG
Where:
k = Boltzmann
’
s constant = 1.380658
×
10
–
23
T = Temperature in degrees Kelvin (273 +
°
C)
R
F
|| R
G
= Parallel resistance of R
F
and R
G
To get the equivalent output noise of the amplifier, just multiply the equivalent input noise density (e
ni
) by the
overall amplifier gain (A
V
).
eno
eniAV
e
ni
1
R
F
R
G
(Noninverting Case)
As the previous equations show, to keep noise at a minimum, small value resistors should be used. As the
closed-loop gain is increased (by reducing R
G
), the input noise is reduced considerably because of the parallel
resistance term. This leads to the general conclusion that the most dominant noise sources are the source
resistor (R
S
) and the internal amplifier noise voltage (e
n
). Because noise is summed in a root-mean-squares
method, noise sources smaller than 25% of the largest noise source can be effectively ignored. This can greatly
simplify the formula and make noise calculations much easier to calculate.
相關PDF資料
PDF描述
THS6043EVM 350 mA, 【12 V ADSL CPE LINE DRIVERS
THS6062D LOW-NOISE ADSL DUAL DIFFERENTIAL RECEIVER
THS6062DGN LOW-NOISE ADSL DUAL DIFFERENTIAL RECEIVER
THS6062EVM RECTIFIER SCHOTTKY 5A30V DO201AD
THS6072D LOW-POWER ADSL DIFFERENTIAL RECEIVER
相關代理商/技術參數
參數描述
THS6043CDG4 功能描述:高速運算放大器 350-mA +/-12V ADSL CPE Ln Drv w/Shtdwn RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS6043CDR 功能描述:高速運算放大器 350-mA +/-12V ADSL CPE Ln Drv w/Shtdwn RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS6043CDRG4 功能描述:高速運算放大器 350-mA +/-12V ADSL CPE Ln Drv w/Shtdwn RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS6043CPWP 功能描述:高速運算放大器 350-mA +/-12V ADSL CPE Ln Drv w/Shtdwn RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
THS6043CPWPG4 功能描述:高速運算放大器 350-mA +/-12V ADSL CPE Ln Drv w/Shtdwn RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*