- 您現在的位置：買賣IC網 > PDF目錄383946 > THS1206EVM (Texas Instruments, Inc.) THS1206 Evaluation Module(THS1206評估板) PDF資料下載
參數資料
| 型號： | THS1206EVM |
| 廠商： | Texas Instruments, Inc. |
| 英文描述： | THS1206 Evaluation Module(THS1206評估板) |
| 中文描述： | THS1206評估模塊（THS1206評估板） |
| 文件頁數： | 16/20頁 |
| 文件大?。?/td> | 143K |
| 代理商： | THS1206EVM |
Requirements
3-2
3.1
Requirements
The Modular THS1206EVM board requires 5 V dc for the analog section of the
ADC. The digital supply (DVdd) and buffer supply (BVdd) can range from 3 V
to 5.25 V. Since the EVM is designed to work with the 5-6K interface board,
JP1 provides direct connection to the common power bus described in
document number SLAU104. Jumpers W9 and W10 should be closed; jumper
W6 provides BVdd options of 5.0 V or 3.3 V.
The following table shows the pin out of JP1:
Signal
Pin Number
1
3
5
7
9
Signal
Unused
+5VA
DGND
Unused
+3.3VD
2
4
6
8
Unused
Unused
AGND
Unused
+5VD
10
Alternate power sources can be applied via various test points located on the
EVM. Refer to the schematic at the end of this document for details. Removing
jumpers W6, W9, and W10 allow the AVdd, DVdd and BVdd voltages to be
applied from completely independent, variable dc sources.
Note: While filters are provided for all power supply inputs, optimal
performance of the EVM requires a clean, well-regulated power source.
3.2
Reference Voltages
The Modular THS1206EVM is configured to use its internal reference through
jumper W1 (see schematic for details). If an external reference is desired,
remove the shunt jumper on W1 and apply the external reference source to
the test point labeled REFIN.
External voltages can also be applied to the REFM and REFP test points if the
device is configured to use the external voltage option, set in configuration reg-
ister one (CR1).
相關PDF資料 |
PDF描述 |
|---|---|
| THS3001D | 420-MHz HIGH-SPEED CURRENT-FEEDBACK AMPLIFIERS |
| THS3002CDGN | 420-MHz HIGH-SPEED CURRENT-FEEDBACK AMPLIFIERS |
| THS3001DGN | 420-MHz HIGH-SPEED CURRENT-FEEDBACK AMPLIFIERS |
| THS3001EVM | 420-MHz HIGH-SPEED CURRENT-FEEDBACK AMPLIFIERS |
| THS3002 | 420-MHz HIGH-SPEED CURRENT-FEEDBACK AMPLIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| THS1206IDA | 功能描述:模數轉換器 - ADC 12-Bit 6 MSPS Quad Channel RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1206IDA | 制造商:Texas Instruments 功能描述:A/D CONVERTER ((NW)) |
| THS1206IDAG4 | 功能描述:模數轉換器 - ADC 12-Bit 6 MSPS Quad Channel RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1206IDAR | 功能描述:模數轉換器 - ADC 12-Bit 6 MSPS Quad Channel RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| THS1206IDARG4 | 功能描述:模數轉換器 - ADC 12-Bit 6 MSPS Quad Channel RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。