參數資料
型號： TFDU6108-TR3
廠商： Vishay Intertechnology,Inc.
英文描述： Fast Infrared Transceiver Module (4 Mbit/s), IrDA Serial Interface Compatible, 2.7 V to 5.5 V Supply Voltage Range
中文描述： 快速紅外收發器模塊（4兆位/秒），紅外串行接口兼容，2.7 V至5.5 V電源電壓范圍
文件頁數： 15/27頁
文件大小： 940K
代理商： TFDU6108-TR3
VISHAY
TFDU6108
Vishay Semiconductors
Document Number 82537
Rev. 1.6, 25-Jun-04
www.vishay.com
15
Appendix B
Application Guideline
In the following some guideline is given for handling
the TFDU6108 in an application ambient, especially
for testing. It is also a guideline for interfacing with a
controller. We recommend to use for first evaluation
the Vishay IRM1802 controller. For more information
see the special data sheet. Driver software is avail-
able on request. Contact irdc@vishay.com.
Serial Interface Capability of the Vishay
IrDA Transceivers Abstract
A serial interface allows an infrared controller to com-
municate with one or more infrared transceivers. The
basic specification of IrDA
specified interface is
described in "Serial Interface for Transceiver Control,
v 1.0a", IrDA.
This part of the document describes the capabilities of
the serial interface implemented in the Vishay IrDA
transceivers TFDU8108 and TFDU6108. The VFIR
(16 Mbit/s) and FIR (4 Mbit/s) programmable versions
are using the same interface specification (with spe-
cific identification and programming).
IrDA Serial Interface Basics
The
s
erial
i
nterface for
t
ransceiver
c
ontrol (SITC) is a
master/slave synchronous serial bus which uses the
Txd and Rxd as data lines and the SCLK as clock line
with a minimum period of 250 ns. The transceiver
works always as slave and jump into SITC mode on
the first rising edge of the clock line remaining there
until the command phase is finished. After power on it
is required an initial phase for
≥
30 clock cycles at Txd
is continuous low before the transmitter can be pro-
grammed. If Txd assume high during the initial phase
then must start the initial phase again.
The data transfer is organized by one byte preceded
by one start bit. The SITC allows the communication
between infrared controller and transceiver through
write and read transaction. The SITC consists of two
store blocks with different functions. The store block
called Extended Indexed Registers contain the vari-
ous supported functionality of the device and can be
read only. The other Main Control Registers allow
write and read transaction and store the executable
configuration of the device.
Any configuration is executed after the command
phase is completed.
Power - up defaults
After power on the transceiver has to stay by definition in the following default mode shown in the table. The default mode of the TFDU6108
is different from the originally defined IrDA Serial Interface default mode. The implemented deviation from the standard was a market re-
quest because only in this way a requested quick function test is possible with the TFDU6108 without the need to connect to a programming
device.
Function
Power Mode
RX
TX_LED
APEN
Infrared Mode
Transmitter Power
Addressing
The transceiver is addressable with three address bits. There are individual and common addresses with the following values.
Description
Individual address
Mask programmable
Common (broadcast) address
TFDU6108
active (!)
active
active
enabled
SIR
defined SIR level
Address value A [2:0]
001
111
相關PDF資料
PDF描述
TFDU6108-TT3 Fast Infrared Transceiver Module (4 Mbit/s), IrDA Serial Interface Compatible, 2.7 V to 5.5 V Supply Voltage Range
TFDU8108 Very Fast IrDA in Standard package
TFK3080D npn silicon tripleton power transistor
TFMM5560 Photo Modules for PCM Remote Control Systems
TFMM5370 Photo Modules for PCM Remote Control Systems
相關代理商/技術參數
參數描述
TFDU6108-TR3 19 制造商:Vishay Angstrohm 功能描述:IRDA TRANSCEIVER FIR BABYFACE MOLD-
TFDU6108-TR3 19 功能描述:紅外收發器 IRDA TRANSCEIVER FIR BABYFACE MOLD- RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel
TFDU6108-TR319 功能描述:紅外收發器 FIR 4Mbit/s 2.7-5.5V Op Voltage RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel
TFDU6108-TT3 功能描述:紅外收發器 FIR 4Mbit/s 2.7-5.5V Op Voltage RoHS:否 制造商:Vishay Semiconductors 波長:900 nm 連續數據傳輸:115.2 Kbit/s 傳輸距離:1 m 輻射強度:60 mW/sr 半強度角度:44 deg 脈沖寬度:2 us 最大上升時間:100 ns 最大下降時間:100 ns LED 電源電壓:- 0.5 V to 6 V 最大正向電流:80 mA 工作電壓:2.4 V to 5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 尺寸:6 mm x 3.1 mm x 1.9 mm 封裝 / 箱體: 封裝:Reel
TFDU6108-TT3 19 制造商:Vishay Semiconductors 功能描述:IRDA TRANSCEIVER FIR BABYFACE MOLD- - Tape and Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*