- 您現在的位置：買賣IC網 > PDF目錄384971 > TFDU5103-TR3 (Vishay Intertechnology,Inc.) Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation PDF資料下載
參數資料
| 型號： | TFDU5103-TR3 |
| 廠商： | Vishay Intertechnology,Inc. |
| 英文描述： | Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation |
| 中文描述： | 快速紅外收發器模塊（，補償1.152兆位/秒）為2.7 V至5.5 V工作電壓 |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 420K |
| 代理商： | TFDU5103-TR3 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
www.vishay.com
2
Document Number 82618
Rev. 1.2, 24-Jun-04
VISHAY
TFDU5103
Vishay Semiconductors
Block Diagram
Pin Description
Controlled
Driver
Tri-State
Driver
GND
Txd
Rxd
Vcc2
Vcc1
Amplifier
Comparator
SD
Mode
Logic
&
Control
18189
Pin Number
1
Function
V
CC2
IRED Anode
Description
I/O
Active
Connect IRED anode directly to V
CC2
. For voltages higher than 3.6 V an
external resistor might be necessary for reducing the internal power
dissipation.An unregulated separate power supply can be used at this pin.
IRED cathode, internally connected to driver transistor
This input is used to transmit serial data when SD is low. An on-chip
protection circuit disables the LED driver if the Txd pin is asserted for longer
than 80
μ
s. When used in conjunction with the SD pin, this pin is also used to
receiver speed mode.
Received Data Output, push-pull CMOS driver output capable of driving a
standard CMOS or TTL load. No external pull-up or pull-down resistor is
required.
Floating with a weak pull-up of 500 k
(typ.) in shutdown
mode.
Shutdown, also used for dynamic mode switching. Setting this pin active
places the module into shutdown mode. On the falling edge of this signal, the
state of the Txd pin is sampled and used to set receiver low bandwidth (Txd
= Low, SIR) or high bandwidth (Txd = High, MIR and FIR) mode. Will be
overwritten by the mode pin input, which must float, when dynamic
programming is used.
Supply Voltage
2
3
IRED Cathode
Txd
I
HIGH
4
Rxd
O
LOW
5
SD
I
HIGH
6
V
CC1
Mode
7
HIGH: High speed mode, MIR and FIR; LOW: Low speed mode, SIR only
(see chapter "Mode Switching").
Output function: The mode pin can also be used to indicate the dynamically
programmed mode. The maximum load is limited to 50 pF. High indicates
MIR-, low indicates SIR-mode
Ground
I
Mode
O
8
GND
相關PDF資料 |
PDF描述 |
|---|---|
| TFDU5103-TT3 | Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation |
| TFDU5107 | Integrated Low Profile Transceiver Module for Telecom Applications |
| TFDU5107-TR3 | Integrated Low Profile Transceiver Module for Telecom Applications |
| TFDU5107-TT3 | Integrated Low Profile Transceiver Module for Telecom Applications |
| TFDU5307 | IrDA with long Link Distance, works as Remote Controll; |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TFDU5103-TR3 19 | 制造商:Vishay Angstrohm 功能描述:IRDA TRANSCEIVER MIR BABYFACE MOLD- |
| TFDU5103-TT3 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Fast Infrared Transceiver Module (MIR, 1.152 Mbit/s) for 2.7 V to 5.5 V Operation |
| TFDU5107 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Low Profile Transceiver Module for Telecom Applications 9.6 kbit/s to 1.152 Mbit/s Data Transmission Rate |
| TFDU5107_05 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Low Profile Transceiver Module for Telecom Applications 9.6 kbit/s to 1.152 Mbit/s Data Transmission Rate |
| TFDU5107-TR3 | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Low Profile Transceiver Module for Telecom Applications 9.6 kbit/s to 1.152 Mbit/s Data Transmission Rate |
發布緊急采購，3分鐘左右您將得到回復。