- 您現在的位置：買賣IC網 > PDF目錄384968 > TE28F016B3B150 (INTEL CORP) SMART 3 ADVANCED BOOT BLOCK BYTE-WIDE PDF資料下載
參數資料
| 型號： | TE28F016B3B150 |
| 廠商： | INTEL CORP |
| 元件分類： | DRAM |
| 英文描述： | SMART 3 ADVANCED BOOT BLOCK BYTE-WIDE |
| 中文描述： | 2M X 8 FLASH 3V PROM, 150 ns, PDSO40 |
| 封裝： | 10 X 20 MM, TSOP-40 |
| 文件頁數： | 28/49頁 |
| 文件大?。?/td> | 408K |
| 代理商： | TE28F016B3B150 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
SMART 3 ADVANCED BOOT BLOCK
–BYTE-WIDE
E
28
PRELIMINARY
After any program or block erase operation is
complete (even after V
PP
transitions down to
V
PPLK
), the CUI must be reset to read array mode
via the Read Array command if access to the flash
memory array is desired.
Refer to AP-617 Additional Flash Data Protection
Using V
PP
, RP#, and WP#for a circuit-level
description of how to implement the protection
schemes discussed in Section 3.5.
3.7
Power Supply Decoupling
Flash memory’s power switching characteristics
require
careful
device
designers should consider three supply current
issues:
1.
Standby current levels (I
CCS
)
2.
Active current levels (I
CCR
)
3.
Transient peaks produced by falling and rising
edges of CE#.
decoupling.
System
Transient current magnitudes depend on the device
outputs’ capacitive and inductive loading. Two-line
control and proper decoupling capacitor selection
will suppress these transient voltage peaks. Each
flash device should have a 0.1 μF ceramic
capacitor connected between each V
CC
and GND,
and between its V
PP
and GND. These high-
frequency, inherently low-inductance capacitors
should be placed as close as possible to the
package leads.
3.7.1
V
TRACE ON PRINTED CIRCUIT
BOARDS
Designing for in-system writes to the flash memory
requires special consideration of the V
PP
power
supply trace by the printed circuit board designer.
The V
PP
pin supplies the flash memory cells current
for programming and erasing. V
PP
trace widths and
layout should be similar to that of V
CC
. Adequate
V
PP
supply traces, and decoupling capacitors
placed adjacent to the component, will decrease
spikes and overshoots.
相關PDF資料 |
PDF描述 |
|---|---|
| TE28F016B3T120 | SMART 3 ADVANCED BOOT BLOCK BYTE-WIDE |
| TE28F016B3T150 | SMART 3 ADVANCED BOOT BLOCK BYTE-WIDE |
| TEA0652 | MONOLITHISCHE STEREO IS |
| TEA0654 | MONOLITHISCHE STEREO IS |
| TEA1017 | 13 BIT SERIES PARALLEL CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TE28F016B3B90 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:SMART 3 ADVANCED BOOT BLOCK 4-, 8-, 16-, 32-MBIT FLASH MEMORY FAMILY |
| TE28F016B3BA110 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3 Volt Advanced Boot Block Flash Memory |
| TE28F016B3BA90 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3 Volt Advanced Boot Block Flash Memory |
| TE28F016B3T110 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:SMART 3 ADVANCED BOOT BLOCK 4-, 8-, 16-, 32-MBIT FLASH MEMORY FAMILY |
| TE28F016B3T120 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:SMART 3 ADVANCED BOOT BLOCK BYTE-WIDE |
發布緊急采購，3分鐘左右您將得到回復。