參數資料
型號： TDA9875A
廠商： NXP SEMICONDUCTORS
元件分類： 消費家電
英文描述： Digital TV Sound Processor DTVSP
中文描述： SPECIALTY CONSUMER CIRCUIT, PDIP64
封裝： SHRINK, PLASTIC, DIP
文件頁數： 12/96頁
文件大?。?/td> 296K
代理商： TDA9875A
1999 Dec 20
12
Philips Semiconductors
Product specification
Digital TV Sound Processor (DTVSP)
TDA9875A
6.1.8
NICAM
AUTO
-
MUTE
This function is enabled by setting bit AMUTE to logic 0
(see Section 10.3.11).
Upper and lower error limits may be defined by writing
appropriate values to two registers in the I
2
C-bus section
(see Sections 10.3.13 and 10.3.14). When the number of
errors in a 128 ms period exceeds the upper error limit the
auto-mute function will switch the output sound from
NICAM to whatever sound is on the first sound carrier
(FM or AM). When the error count is smaller than the lower
error limit the NICAM sound is restored.
The auto-mute function can be disabled by setting
bit AMUTE to logic 1. In this condition clicks become
audible when the error count increases; the user will hear
a signal of degrading quality.
A decision to enable/disable the auto-muting is taken by
the microcontroller based on an interpretation of the
application control bits C1, C2, C3 and C4 and, possibly,
any additional strategy implemented by the set maker in
the microcontroller software.
For NICAM L applications, it is recommended to
demodulate AM sound in the first sound IF and connect
the audio signal to the mono input of the TDA9875A.
By setting bit AMSEL (see Section 10.3.11), the
auto-mute function will switch to the audio ADC instead of
switching to the first sound carrier. The ADC source
selector (see Section 10.3.20) should be set to mono
input, where the AM sound signal should be connected.
6.1.9
C
RYSTAL OSCILLATOR
The circuitry of the crystal oscillator is fully integrated, only
the external 24.576 MHz crystal is needed (see Fig.10).
6.1.10
T
EST PINS
Test pins TEST1 and TEST2 are active HIGH and in the
normal operating mode of the device they are connected
to V
SSD1
. Test functions are for manufacturing tests only
and are not available to customers. Without external
circuitry these pins are pulled down to a LOW level with
internal resistors.
6.1.11
P
OWER FAIL DETECTOR
The power fail detector monitors the internal power supply
for the digital part of the device. If the supply has
temporarily been lower than the specified lower limit, the
Power-on reset bit POR (see Section 10.4.1), will be set to
logic 1.
Bit CLRPOR (see Section 10.3.2) resets the Power-on
reset flip-flop to LOW. If this is detected, an initialization of
the TDA9875A has to be carried out to ensure reliable
operation.
6.1.12
P
OWER
-
ON RESET
The reset is active LOW. In order to perform a reset at
power-up, a simple RC circuit may be used which consists
of the integrated passive pull-up resistor and an external
capacitor connected to ground. The pull-up resistor has a
nominal value of 50 k
, which can easily be measured
between pins CRESET and V
DDD2
. Before the supply
voltage has reached a certain minimum, the state of the
circuit is completely undefined, and it remains in this
undefined state unless a reset is applied.
The reset is guaranteed to be active when:
The power supply is within the specified limits
(4.75 and 5.5 V)
The crystal oscillator is functioning
The voltage at pin CRESET is below 0.3V
DDD
(1.5 V if
V
DDD
= 5.0 V, typically below 1.8 V).
The required capacitor value depends on the gradient of
the rising power supply voltage. The time constant of the
RC circuit should be clearly larger than the rise time of the
power supply, to make sure that the reset condition is
always satisfied (see Fig.4), even considering the
tolerance spread. To avoid problems with a too slow
discharging of the capacitor at power-down, it may be
helpful to add a diode from pin CRESET to V
DDD
. It should
be noted that the internal ESD protection diode does not
help here as it only conducts at higher voltages. Under
difficult power supply conditions (e.g. very slow or
non-monotonic ramp-up), it is recommended to drive the
reset line from a microcontroller port or the like.
handbook, halfpage
MHB595
reset active
guaranteed
1.5
5
voltage
(V)
t
VCRESET
<
0.3VDDD
VDDD
>
4.75 V
Fig.4 Reset at power-on.
相關PDF資料
PDF描述
TDA9875AH Digital TV Sound Processor DTVSP
TDA9875 Digital TV Sound Processor DTVSP
TDA9965 12-bit, 5.0 V, 30 Msps analog-to-digital interface for CCD cameras
TDZ10 Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode
TDZ11 Low Current Operation at 250 ，Low Reverse Leakage,Low Noise Zener Diode
相關代理商/技術參數
參數描述
TDA9875AH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Digital TV Sound Processor DTVSP
TDA9875AH/V2,557 功能描述:IC SOUND PROC DGTL TV 64QFP RoHS:是 類別:集成電路 (IC) >> 線性 - 音頻處理 系列:- 其它有關文件:STA321 View All Specifications 標準包裝:1 系列:Sound Terminal™ 類型:音頻處理器 應用:數字音頻 安裝類型:表面貼裝 封裝/外殼:64-LQFP 裸露焊盤 供應商設備封裝:64-LQFP EP（10x10） 包裝:Digi-Reel® 其它名稱:497-11050-6
TDA9880 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Alignment-free multistandard vision and FM sound IF-PLL demodulator
TDA9880T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Alignment-free multistandard vision and FM sound IF-PLL demodulator
TDA9881 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Alignment-free vision and FM sound IF PLL demodulator for negative modulated TV standards
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*