參數資料
型號： TDA8943
廠商： NXP Semiconductors N.V.
元件分類： 運動控制電子
英文描述： 6 W mono Bridge Tied Load BTL audio amplifier
中文描述： 6聲道橋接負載橋接音頻放大器
文件頁數： 5/20頁
文件大?。?/td> 358K
代理商： TDA8943
Philips Semiconductors
TDA8943SF
6 W mono Bridge Tied Load (BTL) audio amplifier
Product specification
Rev. 02 — 7 April 2000
5 of 20
9397 750 06865
Philips Electronics N.V. 2000. All rights reserved.
8.2.2
Headroom
Typical CD music requires at least 12 dB (factor 15.85) dynamic headroom –
compared to the average power output – for transferring the loudest parts without
distortion. At V
CC
= 12 V, R
L
= 8
and P
o
= 4 W at THD = 0.1% (see
Figure 6
), the
Average Listening Level (ALL) – music power – without any distortion yields:
P
o(ALL)
= 4 W/15.85 = 252 mW.
The power dissipation can be derived from
Figure 11 on page 10
for 0 dB
respectively 12 dB headroom.
For the average listening level a power dissipation of 1.8 W can be used for a
heatsink calculation.
8.3 Mode selection
The TDA8943SF has three functional modes, which can be selected by applying the
proper DC voltage to pin MODE. See
Figure 4
and
5
for the respective DC levels,
which depend on the supply voltage level. The MODE pin can be driven by a 3-state
logic output stage: e.g. a microcontroller with additional components for DC-level
shifting.
Standby —
In this mode the current consumption is very low and the outputs are
floating. The device is in standby mode when (V
CC
0.5 V) < V
MODE
< V
CC
, or when
the MODE pin is left floating (high impedance). The power consumption of the
TDA8943SF will be reduced to <0.18 mW.
Mute —
In this mode the amplifier is DC-biased but not operational (no audio output);
t
he DC level of the input and output pins remain on half the supply voltage. This
allows the input coupling and Supply Voltage Ripple Rejection (SVRR) capacitors to
be charged to avoid pop-noise. The device is in mute mode when
3 V < V
MODE
< (V
CC
1.5 V).
Operating —
In this mode the amplifier is operating normally. The operating mode is
activated at V
MODE
< 0.5 V.
8.3.1
Switch-on and switch-off
To avoid audible plops during supply voltage switch-on or switch-off, the device is set
to standby mode before the supply voltage is applied (switch-on) or removed
(switch-off).
The switch-on and switch-off time can be influenced by an RC-circuit on the MODE
pin. Rapid on/off switching of the device or the MODE pin may cause ‘click- and
pop-noise’. This can be prevented by proper timing of the RC-circuit on the MODE
pin.
Table 4:
Headroom
0 dB
12 dB
Power rating as function of headroom
Power output (THD = 0.1%)
P
o
= 4 W
P
o(ALL)
= 252 mW
Power dissipation (P)
3.8 W
1.8 W
相關PDF資料
PDF描述
TDA8946J 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier(2 x 15W立體聲BTL音頻放大器)
TDA8946 2 x 15 W stereo Bridge Tied Load BTL audio amplifier
TDA9160 PAL/NTSC/SECAM decoder/sync processor(PAL/NTSC/SECAM譯碼器/ 同步處理器)
TDA935X TV signal processor-Teletext decoder with embedded m-Controller
TDA936X TV signal processor-Teletext decoder with embedded m-Controller
相關代理商/技術參數
參數描述
TDA8943SF 制造商:PHILPS 功能描述:
TDA8943SF/N1,112 功能描述:音頻放大器 6W MONO BTL PWR AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TDA8943SF/N1.112 制造商:NXP Semiconductors 功能描述:AMP AUDIO POWER SINGLE 8943 SIL-9
TDA8944 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2 x 7 W stereo Bridge Tied Load BTL audio amplifier
TDA8944AJ 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2 x 7 W BTL audio amplifier with DC gain control
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*