- 您現在的位置：買賣IC網 > PDF目錄368631 > TDA8943 (NXP Semiconductors N.V.) 6 W mono Bridge Tied Load BTL audio amplifier PDF資料下載
參數資料
| 型號： | TDA8943 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 運動控制電子 |
| 英文描述： | 6 W mono Bridge Tied Load BTL audio amplifier |
| 中文描述： | 6聲道橋接負載橋接音頻放大器 |
| 文件頁數： | 14/20頁 |
| 文件大小： | 358K |
| 代理商： | TDA8943 |
Philips Semiconductors
TDA8943SF
6 W mono Bridge Tied Load (BTL) audio amplifier
Product specification
Rev. 02 — 7 April 2000
14 of 20
9397 750 06865
Philips Electronics N.V. 2000. All rights reserved.
14.2 Thermal behaviour and heatsink calculation
The measured maximum thermal resistance of the IC package, R
th(j-mb)
is 18 K/W.
A calculation for the heatsink can be made, with the following parameters:
T
amb(max)
= 50
°
C
V
CC
= 12 V and R
L
= 8
T
j(max)
= 150
°
C.
R
th(tot)
is the total thermal resistance between the junction and the ambient
including the heatsink. In the heatsink calculations the value of R
th(mb-h)
is ignored.
At V
CC
= 12 V and R
L
= 8
the measured worst-case sine-wave dissipation is 3.8 W;
see
Figure 11
. For T
j(max)
= 150
°
C the temperature raise – caused by the power
dissipation – is: 150 – 50 = 100
°
C.
P
×
R
th(tot)
= 100
°
C
R
th(tot)
= 100/3.8 = 26.3 K/W
R
th(h-a)
= R
th(tot)
– R
th(j-mb)
= 26.3 – 18 = 8.3 K/W.
The calculation above is for an application at worst-case sine-wave output signals. In
practice music signals will be applied, which decreases the maximum power
dissipation to approximately half of the sine-wave power dissipation (see
Section 8.2.2
). This allows for the use of a smaller heatsink:
P
×
R
th(tot)
= 100
°
C
R
th(tot)
= 100/1.8 = 55.5 K/W
R
th(h-a)
= R
th(tot)
– R
th(j-mb)
= 55.5 – 18 = 37.5 K/W.
To increase the lifetime of the IC, T
j(max)
should be reduced to 125
°
C. This requires a
heatsink of approximately 24 K/W for music signals.
15. Test information
15.1 Quality information
The General Quality Specification for Integrated Circuits, SNW-FQ-611Dis
applicable.
15.2 Test conditions
T
amb
= 25
°
C; V
CC
= 12 V; f = 1 kHz; R
L
= 8
; audio pass band 22 Hz to 22 kHz;
unless otherwise specified.
Remark:
In the graphs as function of frequency no bandpass filter was applied; see
Figure 7
and
12
.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8946J | 2 x 15 W stereo Bridge Tied Load (BTL) audio amplifier(2 x 15W立體聲BTL音頻放大器) |
| TDA8946 | 2 x 15 W stereo Bridge Tied Load BTL audio amplifier |
| TDA9160 | PAL/NTSC/SECAM decoder/sync processor(PAL/NTSC/SECAM譯碼器/ 同步處理器) |
| TDA935X | TV signal processor-Teletext decoder with embedded m-Controller |
| TDA936X | TV signal processor-Teletext decoder with embedded m-Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8943SF | 制造商:PHILPS 功能描述: |
| TDA8943SF/N1,112 | 功能描述:音頻放大器 6W MONO BTL PWR AMP RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8943SF/N1.112 | 制造商:NXP Semiconductors 功能描述:AMP AUDIO POWER SINGLE 8943 SIL-9 |
| TDA8944 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2 x 7 W stereo Bridge Tied Load BTL audio amplifier |
| TDA8944AJ | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2 x 7 W BTL audio amplifier with DC gain control |
發布緊急采購，3分鐘左右您將得到回復。