- 您現在的位置：買賣IC網 > PDF目錄368631 > TDA8787A (NXP Semiconductors N.V.) 10-bit, 3.0 V, up to 25 Msps analog-to-digital interface for CCD cameras PDF資料下載
參數資料
| 型號： | TDA8787A |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 10-bit, 3.0 V, up to 25 Msps analog-to-digital interface for CCD cameras |
| 中文描述： | 10位，為3.0 V，高達25 Msps的模擬到數字的CCD相機接口 |
| 文件頁數： | 20/24頁 |
| 文件大?。?/td> | 125K |
| 代理商： | TDA8787A |
2000 Nov 14
20
Philips Semiconductors
Product specification
10-bit, 3.0 V, up to 25 Msps analog-to-digital
interface for CCD cameras
TDA8787A
SOLDERING
Introduction to soldering surface mount packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering is not always suitable
for surface mount ICs, or for printed-circuit boards with
high population densities. In these situations reflow
soldering is often used.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250
°
C. The top-surface temperature of the
packages should preferable be kept below 230
°
C.
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8787 | 10-bit, 3.0 V analog-to-digital interface for CCD cameras |
| TDA8790 | 8-bit, 40 Msps 2.7 to 5.5 V universal analog-to-digital converter |
| TDA8792 | 3.3 V, 25 MHz 8-bit analog-to-digital converter ADC |
| TDA8793HL | 8-bit, low-power, 3 V, 100 Msps Analog-to-Digital Converter ADC |
| TDA8798 | Dual 8-bit, 100 Msps A/D converter with DPGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8787AHL | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:10-bit, 3.0 V, up to 25 Msps analog-to-digital interface for CCD cameras |
| TDA8787AHL/C3,118 | 功能描述:電信線路管理 IC 10-BIT CCD 25MSPS RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| TDA8787AHL/C3,151 | 功能描述:電信線路管理 IC ADC 10BIT 18MSPS RoHS:否 制造商:STMicroelectronics 產品:PHY 接口類型:UART 電源電壓-最大:18 V 電源電壓-最小:8 V 電源電流:30 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:VFQFPN-48 封裝:Tray |
| TDA8787AHL/C3,157 | 功能描述:模數轉換器 - ADC AFE Video 1ADC 10Bit 2.6V/3V 48-Pin RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| TDA8787AHL/S1 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:10-bit, 3.0 V, up to 25 Msps analog-to-digital interface for CCD cameras |
發布緊急采購，3分鐘左右您將得到回復。