- 您現在的位置：買賣IC網 > PDF目錄383941 > TDA8552 (NXP Semiconductors N.V.) 2 x 1.4 W BTL audio amplifiers with digital volume control and headphone sensing PDF資料下載
參數資料
| 型號： | TDA8552 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 運動控制電子 |
| 英文描述： | 2 x 1.4 W BTL audio amplifiers with digital volume control and headphone sensing |
| 中文描述： | 2 × 1.4 W功率，橋接與數字音量控制和傳感耳機音頻放大器 |
| 文件頁數： | 6/28頁 |
| 文件大?。?/td> | 254K |
| 代理商： | TDA8552 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
1998 Jun 02
6
Philips Semiconductors
Preliminary specification
2
×
1.4 W BTL audio amplifiers with digital
volume control and headphone sensing
TDA8552T; TDA8552TS
FUNCTIONAL DESCRIPTION
The TDA8552T is a 2
×
1.4 W BTL audio power amplifier
capable of delivering 2
×
1.4 W output power into an 8
load at THD = 10% using a 5 V power supply. The gain of
the amplifier can be set by the digital volume control.
The gain in the maximum volume setting is 20 dB (low
gain) or 30 dB (high gain). This maximum gain can be
selected by the gain selection pin. The headphone sense
input (HPS) can be used to detect if a headphone is
plugged into the jack connector. If a headphone is plugged
into the jack connector the amplifier switches from the BTL
to the SE mode and the BTL loudspeakers are switched
off. This also results in a reduction of quiescent current
consumption. Using the MODE pin the device can be
switched to the standby condition, the mute condition or
the normal operating condition. The device is protected by
an internal thermal shutdown protection mechanism.
Power amplifier
The power amplifier is a Bridge-Tied Load (BTL) amplifier
with a complementary CMOS output stage. The total
voltage loss for both output power MOS transistors is
within 1 V and with a 5 V supply and an 8
loudspeaker
an output power of 1.4 W can be delivered. The total gain
of this power amplifier can be set at 20 or 30 dB by the
gain selection pin.
Gain selection
The gain selection can be used for a fixed gain setting,
depending on the application. The gain selection pin must
be hard wired to ground (20 dB) or to V
DD
(30 dB). Gain
selecting during the operation is not advised, switching is
not guaranteed plop free.
Input attenuator
The volume control operates as a digitally controlled input
attenuator between the audio input pin and the power
amplifier. In the maximum volume control setting the
attenuation is 0 dB and in the minimum volume control
setting the typical attenuation is 80 dB. The attenuation
can be set in 64 steps by the UP/DOWN pin. Both
attenuators for channels 1 and 2 are separated from each
other and are controlled by there own UP/DOWN pin.
Balance control can be arranged by applying UP/DOWN
pulses only on pins 6 and 7, see Fig.5.
Volume control
Each attenuator is controlled with its own UP/DOWN pin
(trinary input):
Floating UP/DOWN pin: volume remains unchanged
Negative pulses: decreasing volume
Positive pulses: increasing volume.
Each pulse on the UP/DOWN pin results in a change in
64
gain of
(typical value).
In the basic application the UP/DOWN pin is switched to
ground or V
DD
by a double push-button. When the supply
voltage is initially connected, after a complete removal of
the supply, the initial state of the volume control is an
attenuation of 40 dB (low volume), so the gain of the total
amplifier is
20 dB in the low gain setting or
10 dB in the
high gain setting. After powering-up, some positive pulses
have to be applied to the UP/DOWN pin for turning up to
listening volume.
Auto repeat
If the UP/DOWN pin is LOW or HIGH for the wait time (t
wait
in seconds) (one of the keys is pressed) then the device
starts making up or down pulses by itself with a frequency
t
rep
given by
(repeat function).
The wait time and the repeat frequency are set using an
internal RC oscillator with an accuracy of
±
10%.
Volume settings in standby mode
When the device is switched with the MODE select pin to
the mute or the standby condition, the volume control
attenuation setting keeps its value, under the assumption
that the voltage on the V
DD
pin does not fall below the
minimum supply voltage. After switching the device back
to the operation mode, the previous volume setting is
maintained. In the standby mode the volume setting is
maintained as long as the minimum supply voltage is
available. The current consumption is very low,
approximately 1
μ
A (typ.). In battery fed applications the
volume setting can be maintained during battery exchange
if there is a supply capacitor available.
80
1.25 dB
=
-1
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8552T | 2 x 1.4 W BTL audio amplifiers with digital volume control and headphone sensing |
| TDA8763A | 10-bit high-speed low-power ADC |
| TDA8763 | 10-bit high-speed low-power ADC with internal reference regulator |
| TDA9151 | Transient Voltage Suppressor Diodes |
| TDA9830TD-T | Transient Voltage Suppressor Diodes |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8552T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2 x 1.4 W BTL audio amplifiers with digital volume control and headphone sensing |
| TDA8552T/N1,512 | 功能描述:音頻放大器 AUDIO PWR AMP BTL RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8552T/N1,518 | 功能描述:音頻放大器 2X1W CMOS AMP + VOL RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8552T/N1.112 | 制造商:NXP Semiconductors 功能描述:AMP AUDIO POWER DUAL 8552 SOIC20 |
| TDA8552T_02 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:2 x 1.4 W BTL audio amplifiers with digital volume control and headphone sensing |
發布緊急采購，3分鐘左右您將得到回復。