- 您現在的位置：買賣IC網 > PDF目錄383941 > TDA8510 (NXP Semiconductors N.V.) 26 W BTL and 2 x 13 W SE power amplifiers PDF資料下載
參數資料
| 型號： | TDA8510 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 26 W BTL and 2 x 13 W SE power amplifiers |
| 中文描述： | 26糯橋接和2 x 13 W功率東南功率放大器 |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 82K |
| 代理商： | TDA8510 |
1999 Dec 14
5
Philips Semiconductors
Preliminary specification
26 W BTL and 2
×
13 W SE power
amplifiers
TDA8510J
FUNCTIONAL DESCRIPTION
The TDA8510J contains four identical amplifiers and can
be used for two Single-Ended (SE) channels (fixed gain
20 dB) and one Bridge-Tied Load (BTL) channel (fixed
gain 26 dB). Special features of the device are:
Mode select switch (pin 14)
Low standby current (<100
μ
A)
Low switching current (low cost supply switch)
Mute facility.
To avoid switch-on plops, it is advised to keep the amplifier
in the mute mode during
≥
100 ms (charging of the input
capacitors at pins 1, 3, 15 and 17). This can be achieved
by:
Microcontroller control
External timing circuit (see Fig.8).
Diagnostic output (pin 16)
D
YNAMIC
D
ISTORTION
D
ETECTOR
(DDD)
At the onset of clipping of one or more output stages, the
dynamic distortion detector becomes active and pin 16
goes LOW. This information can be used to drive a sound
processor or DC volume control to attenuate the input
signal and thus limit the distortion. The output level of
pin 16 is independent of the number of channels that are
clipping (see Figs 3 and 4).
S
HORT
-
CIRCUIT PROTECTION
When a short-circuit occurs at one or more outputs to
ground or to the supply voltage, the output stages are
switched off until the short-circuit is removed and the
device is switched on again, with a delay of approximately
20 ms, after removal of the short-circuit. During this
short-circuit condition, pin 16 is continuously LOW.
When a short-circuit across the load of one or more
channels occurs the output stages are switched off for
approximately 20 ms. After that time it is checked during
approximately 50
μ
s to see whether the short-circuit is still
present. Due to this duty cycle of 50
μ
s/20 ms the average
current consumption during this short-circuit condition is
very low (approximately 40 mA).
During this short-circuit condition, pin 16 is LOW for 20 ms
and HIGH for 50
μ
s (see Fig.5).
The power dissipation in any short-circuit condition is very
low.
Fig.3 Distortion detector waveform; BTL channel.
handbook, halfpage
V
0
VP
VO
0
t
MGA705
16
Fig.4 Distortion detector waveform; SE channels.
handbook, halfpage
0
VP
VO
t
0
MGA706
V16
相關PDF資料 |
PDF描述 |
|---|---|
| TDA8510J | 26 W BTL and 2 x 13 W SE power amplifiers |
| TDA8511 | 4 x 13 W single-ended power amplifiers |
| TDA8511J | 4 x 13 W single-ended power amplifiers |
| TDA8541 | 1 W BTL audio amplifier |
| TDA8547 | 2 x 1 W BTL audio amplifier with output channel switching |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA8510J | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:26 W BTL and 2 x 13 W SE power amplifiers |
| TDA8510J/N2,112 | 功能描述:音頻放大器 AMP POWER 26W 17-SIL RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TDA8511 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4 x 13 W single-ended power amplifiers |
| TDA8511J | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:4 x 13 W single-ended power amplifiers |
| TDA8511J/N2 | 制造商:NXP Semiconductors 功能描述:Single-ended poweramplifier,TDA8511J/N2 |
發布緊急采購，3分鐘左右您將得到回復。