參數資料
型號： TDA7405
廠商： STMICROELECTRONICS
元件分類： 音頻控制
英文描述： 2 CHANNEL(S), TONE CONTROL CIRCUIT, PQFP44
封裝： 10 X 10 MM, 1.40 MM HEIGHT, TQFP-44
文件頁數： 26/57頁
文件大小： 750K
代理商： TDA7405
Obsolete
Product(s)
- Obsolete
Product(s)
TDA7405
32/57
10.2 InGain + Infilter
The InGain stage allows to adjust the MPX-signal to a magnitude of about 1Vrms internally which is the recom-
mended value. The 4.th order input filter has a corner frequency of 80kHz and is used to attenuate spikes and
noise and acts as an anti-aliasing filter for the following switch capacitor filters.
10.3 Demodulator
In the demodulator block the left and the right channel are separated from the MPX-signal. In this stage also the
19-kHz pilottone is cancelled. For reaching a high channel separation the A631 offers an I2C-bus programmable
roll-off adjustment which is able to compensate the lowpass behavior of the tuner section. If the tuner's attenu-
ation at 38kHz is in a range from 7.2% to 31.0% the A631 needs no external network in front of the MPX-pin.
Within this range an adjustment to obtain at least 40 dB channel separation is possible. The bits for this adjust-
ment are located together with the fieldstrength adjustment in one byte. This gives the possibility to perform an
optimization step during the production of the carradio where the channel separation and the fieldstrength con-
trol are trimmed. The setup of the Stereoblend characteristics which is programmable in a wide range is de-
scribed in 2.8.
10.4 Deemphasis and Highcut
The deemphasis-lowpass allows to choose a time constant between 37.5 and 100s. The highcut control range
will be 2 x tDeemp or 2.7 x tDeemp dependent on the selected time constant (see programming section). The bit
D7 of the hightcut-byte will shift timeconstant and range.
Inside the highcut control range (between VHCH and VHCL) the LEVEL signal is converted into a 5 bit word
which controls the lowpass time constant between tDeemp...3 (3.7) x tDeemp. Thereby the resolution will remain
always 5 bits independently of the absolute voltage range between the VHCH- and VHCL-values. In addition
the maximum attenuation can be fixed between 2 and 10dB.
The highcut function can be switched off by I2C-bus (bit D7, Highcut byte set to "0").
The setup of the highcut characteristics is described in 4.9.
10.5 PLL and Pilottone-Detector
The PLL has the task to lock on the 19kHz pilottone during a stereo-transmission to allow a correct demodula-
tion. The included pilottone-detector enables the demodulation if the pilottone reaches the selected pilottone
threshold VPTHST. Two different thresholds are available. The detector output (signal STEREO, see Blockdi-
agram) can be checked by reading the status byte of the A631 via I2C-bus. During a Softmute the PLL can be
set into "Hold"-mode which freezes the PLL's state (bit D4, Softmute byte). After releasing the Softmute the PLL
will again follow the input signal only by correcting the phase error.
10.6 Fieldstrength Control
The fieldstrength input is used to control the highcut- and the stereoblend-function. In addition the signal can be
also used to control the noiseblanker thresholds and as input for the multipath detector. These additional func-
tions are described in sections 3.3 and 4.
10.7 LEVEL-Input and -Gain
To suppress undesired high frequency modulation on the highcut- and stereoblend-control signal the LEVEL
signal is lowpass filtered firstly. The filter is a combination of a 1.st-order RC-lowpass at 53kHz (working as anti-
aliasing filter) and a 1.st-order switched-capacitor-lowpass at 2.2kHz. The second stage is a programmable gain
stage to adapt the LEVEL signal internally to different IF-devices (see Testmode section 5: LEVELHCC). The
gain is widely programmable in 16 steps from 0dB to 6dB (step=0.4dB). These 4 bits are located together with
the Roll-Off bits in the "Stereodecoder-Adjustment"-byte to simplify a possible adjustment during the production
of the carradio. This signal controls directly the Highcut stage whereas the signal is filtered again (fc=100Hz)
before the stereoblend stage (see Figure 25).
相關PDF資料
PDF描述
TDA7406T SPECIALTY CONSUMER CIRCUIT, PQFP44
TDA7407TR SPECIALTY CONSUMER CIRCUIT, PQFP44
TDA7407 SPECIALTY CONSUMER CIRCUIT, PQFP44
TDA7409D 1 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO20
TDA7410NDTR 2 CHANNEL(S), TONE CONTROL CIRCUIT, PDSO20
相關代理商/技術參數
參數描述
TDA7405_04 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:EQUALIZER CARRADIO SIGNAL PROCESSOR
TDA7405TR 功能描述:處理器 - 專門應用 EQUALIZER CAR RADIO SIGNAL PROCESSOR RoHS:否 制造商:Freescale Semiconductor 類型:Multimedia Applications 核心:ARM Cortex A9 處理器系列:i.MX6 數據總線寬度:32 bit 最大時鐘頻率:1 GHz 指令/數據緩存: 數據 RAM 大小:128 KB 數據 ROM 大小: 工作電源電壓: 最大工作溫度:+ 95 C 安裝風格:SMD/SMT 封裝 / 箱體:MAPBGA-432
TDA7406 功能描述:音頻 DSP Car Radio Signal RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
TDA7406T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:CAR RADIO SIGNAL PROCESSOR
TDA7406TR 功能描述:音頻 DSP INFOTAINMENT SIGNAL RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*