- 您現在的位置：買賣IC網 > PDF目錄383940 > TDA5155 (NXP Semiconductors N.V.) Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads PDF資料下載
參數資料
| 型號： | TDA5155 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
| 中文描述： | 預硬盤驅動器硬盤驅動器放大器MR-read/inductive寫磁頭 |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 112K |
| 代理商： | TDA5155 |
1997 Apr 08
9
Philips Semiconductors
Preliminary specification
Pre-amplifier for Hard Disk Drive (HDD)
with MR-read/inductive write heads
TDA5155
8.3
Sleep mode
In sleep mode, the device is accessible via the serial
interface. All circuits are inactive, except the circuits of the
CMOS serial interface and the circuitry which forces the
data registers to their default values at power-up and
which fixes the DC level of outputs RDx and RDy (required
when operating with more than one amplifier). Typical
static current consumption is
30
μ
A. Dynamic current
consumption during operation of the serial interface in
sleep mode due to external activity at the inputs to the
serial interface is not included. In all modes, including the
sleep mode, data registers can be programmed. Sleep is
the default mode at power-up. Switching to other modes
takes less than 0.1 ms.
8.4
Standby mode
The circuit can be put in standby mode using the serial
interface. In standby mode, the typical DC current
consumption is 330
μ
A. Transients from standby mode to
active mode are two orders of magnitude shorter than from
sleep mode to active mode. This is important in the case
of cylinder mode operation with multiple amplifiers.
All amplifiers can operate from standby mode and all head
switch times can be kept just as short as in the case of
operation with a single amplifier. Head switch times are
summarized in the switching characteristics.
8.5
Active mode
Active mode is either read mode or write mode depending
on the status of the R/W pin.
8.6
Bi-directional serial interface
The serial interface is used for programming the device
and for reading of status information. 16 bits (8 bits for
data and 8 for address) are used to program the device.
The serial interface requires 3 pins: SDATA, SCLK and
SEN. These pins (and R/W as well) are CMOS inputs.
The logic input R/W has an internal 20 k
pull-up resistor
and the SEN logic input has an internal 20 k
pull-down
resistor. Thus, in case the SEN line is opened, no data will
be registered and in case the R/W line is opened, the
device will never be in write mode.
SDATA: serial data; bi-directional data interface. In all
circumstances,
the LSB is transmitted first
.
SCLK: serial clock; 25 MHz clock frequency.
SEN: serial enable; data transfer takes place when SEN is
HIGH. When SEN is LOW, data and clock signals are
prohibited from entering the circuit.
Three phases in the communication are distinguishable:
addressing, programming and reading. Each
communication sequence starts with an addressing
phase, followed by either a programming phase or a
reading phase.
8.6.1
A
DDRESSING
When SEN goes HIGH, bits are latched in at rising edges
of SCLK. The first eight bits a7 to a0 (starting with a0) are
shifted serially into an address register. If SEN goes LOW
before 16 bits have been received, the operation is
ignored. When more than 16 bits (address and data) are
latched in before SEN goes LOW, the first 8 bits are
interpreted as an address and the last 8 bits as data. SEN
should go HIGH at least 5 ns before the first rising edge of
SCLK. Data should be valid at least 5 ns before and after
a rising edge of SCLK. The first six bits a5 to a0 constitute
the register address. Bit a6 is unused. If bit a7 = logic 0,
a PROGRAMMING sequence starts. If bit a7 = logic 1,
READING data from the pre-amplifier can start.
8.6.2
P
ROGRAMMING DATA
If a7 = 0, the last eight bits d7 to d0 before SEN goes LOW
are shifted into an input register. When SEN goes LOW,
the communication sequence is ended and the data in the
input register is copied in parallel to the data register that
corresponds to the decoded address a0 to a5. SEN
should go LOW at least 5 ns after the last rising edge of
SCLK. See Fig.3 for the timing diagram of the
programming.
8.6.3
R
EADING DATA
Immediately after the IC detects that a7 = logic 1, data
from the data register (address a5 to a0) is copied in
parallel to the input register. Two wait clock cycles must
follow before the controller can start inputting data. At the
first falling edge of SCLK after the 2 wait rising edges of
SCLK, the LSB d0 is placed on SDATA line followed by d1
at the next falling edge of SCLK etc. If SEN goes LOW
before 8 address bits (a7 to a0) have been detected, the
communication is ignored. If SEN goes LOW before the
8 data bits have been sent out of the IC, the reading
sequence is immediately interrupted. See Fig.4 for the
timing diagram of the reading via the serial interface.
相關PDF資料 |
PDF描述 |
|---|---|
| TDA5155X | Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
| TDA5240 | Brushless DC motor drive circuit |
| TDA5240T | Brushless DC motor drive circuit |
| TDA5241 | Brushless DC motor drive circuit |
| TDA5330T | VHF, UHF and Hyperband mixer/oscillator for TV and VCR 3-band tuners |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA5155X | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Pre-amplifier for Hard Disk Drive HDD with MR-read/inductive write heads |
| TDA5200 | 功能描述:射頻接收器 CNTRL RF RECEIVER 870MHZ 5V RoHS:否 制造商:Skyworks Solutions, Inc. 類型:GPS Receiver 封裝 / 箱體:QFN-24 工作頻率:4.092 MHz 工作電源電壓:3.3 V 封裝:Reel |
| TDA5200_10 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:ASK Single Conversion Receiver |
| TDA5200T | 制造商:Infineon Technologies AG 功能描述:RF Receiver ASK 5V 28-Pin TSSOP T/R |
| TDA5200XUMA1 | 制造商:Infineon Technologies AG 功能描述:RF Receiver ASK 5V T/R 制造商:Infineon Technologies AG 功能描述:CONTROL - Tape and Reel 制造商:Infineon Technologies AG 功能描述:CONTROL - Cut TR (SOS) 制造商:Infineon Technologies 功能描述:Infineon Technologies TDA5200XUMA1 RF Transceivers 制造商:Infineon Technologies AG 功能描述:IC LP SGL CONV ASK P-TSSOP-28 |
發布緊急采購，3分鐘左右您將得到回復。