- 您現在的位置：買賣IC網 > PDF目錄383989 > TDA4882 (NXP SEMICONDUCTORS) Advanced monitor video controller for OSD PDF資料下載
參數資料
| 型號： | TDA4882 |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 消費家電 |
| 英文描述： | Advanced monitor video controller for OSD |
| 中文描述： | SPECIALTY CONSUMER CIRCUIT, PDIP20 |
| 封裝： | 0.300 INCH, PLASTIC, SOT-146-1, DIP-20 |
| 文件頁數： | 12/28頁 |
| 文件大小： | 263K |
| 代理商： | TDA4882 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
1997 Sep 04
12
Philips Semiconductors
Product specification
Advanced monitor video controller for OSD
TDA4882
11. The signal-to-noise ratio is calculated by the formula (frequency range 1 to 70 MHz):
S
N
dB
12. Large output swing e.g. I
o(b-w)
= 50 mA leads to signal-dependent power dissipation in output transistors.
Thermal V
BE
variation is compensated.
13. Composite signals will not disturb normal operation because an internal clipping circuit cuts all signal parts below
black level.
14. The output current approximately follows the equation
for V
o
> V
bl(SO)
and with
R
O
= external resistor at voltage output to ground. The external RC combination (Fig.1) at pins 19, 16 and 13
(voltage outputs) enables peak currents during transients.
15. Frequency response, crosstalk and pulse response have been measured at voltage outputs on a special
printed-circuit board with 50
line in/out connections and without peaking, see Chapter 11.
16. Crosstalk between any two voltage outputs (e.g. channels 1 and 2).
a)
Input conditions
: one channel (channel 1) with nominal input signal and minimum rise time. The inputs of the
other channels capacitively coupled to ground (channels 2 and 3). Gain pins 3 and 11 open-circuit.
b)
Output conditions
: output signal of channel 1 is set by contrast control voltage, to V
o(b-w)
= V
o(VOUT1)
= 0.7 V,
the rise time should be 5 ns. Output signal of channel 2 then is V
o(b-w)
= V
o(VOUT2)
.
c)
Transient crosstalk
:
dB
d) Crosstalk as a function of frequency has been measured without peaking circuit, with nominal input signal and
nominal settings.
17. The internal threshold voltages are derived from a stabilized voltage. The internal pulses are generated while the
input pulses are higher than the thresholds. Voltages less than
0.1 V at pins 9 and 10 can influence black-level
control and should be avoided.
18. The delay between HBL input pulse (horizontal blanking) and output signal blanking pulse and also brightness
blanking (
V
bl
), at the voltage outputs, depends on the input rise time of the HBL pulse. The specified values for
t
d(Hblank)
are valid for HBL rise times greater than 100 ns only.
19. For 75 ns/V < t
r(CL),
t
f(CL)
< 240 ns/V, generation of internal input clamping and blanking pulse is not defined. Pulses
not exceeding the threshold of input clamping (typical 3 V) will be detected as blanking pulses.
---
20
peak-to-peak value of the nominal signal output voltage
log
×
=
I
o
V
o
R
O
-1
2.2 k
------1
+
500
μ
A
–
=
α
ct(tr)
20
V
V
o(VOUT1)
------------------------
log
×
=
相關PDF資料 |
PDF描述 |
|---|---|
| TDA4884 | Advanced monitor video controller for OSD |
| TDA4885 | 150 MHz video controller with I2C-bus |
| TDA4886A | 140 MHz video controller with I2C-bus |
| TDA4886 | 140 MHz video controller with I2C-bus |
| TDA4887 | 160 MHz bus-controlled monitor video preamplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA4883 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Non-VGA Video Controller |
| TDA4884 | 制造商:NXP Semiconductors 功能描述:3 CHANNEL, VIDEO PREAMPLIFIER, PDIP20 |
| TDA4885 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| TDA4885/V2 | 制造商:NXP Semiconductors 功能描述: |
| TDA4886 | 制造商:PHILIPS-SEMI 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。