- 您現在的位置：買賣IC網 > PDF目錄384964 > TDA1085C (ON SEMICONDUCTOR) Universal Motor Speed Controller(通用電機速度控制器) PDF資料下載
參數資料
| 型號： | TDA1085C |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 運動控制電子 |
| 英文描述： | Universal Motor Speed Controller(通用電機速度控制器) |
| 中文描述： | UNIVERSAL MOTOR CONTROLLER, 0.2 A, PDIP16 |
| 封裝： | PLASTIC, DIP-16 |
| 文件頁數： | 7/12頁 |
| 文件大?。?/td> | 102K |
| 代理商： | TDA1085C |
TDA1085C
http://onsemi.com
7
Trigger pulse duration can be disturbed by noise signals
generated by the triac itself, which interfere within Pins 14
and 16, precisely those which determine it. While easily
visible, this effect is harmless.
The triac must be protected from high AC line dV/dt
during external disturbances by 100 nF x 100
network.
Shunt resistor must be as non–inductive as possible. It can
be made locally by using constantan alloy wire.
When the load is a DC fed universal motor through a
rectifier bridge, the triac must be protected from
commutating dV/dt by a 1.0 to 2.0 mH coil in series with
MT2.
Synchronization functions are performed by resistors
sensing AC line and triac conduction. 820 k values are
normal but could be reduced down to 330 k in order to detect
the “zeros” with accuracy and to reduce the residual DC line
component below 20 mA.
Current Limitation
The current limiter starts to discharge Pin 7 capacitor
(reference speed) as the motor current reaches the designed
threshold level. The loop gain is determined by the resistor
connecting Pin 3 to the series shunt. Experience has shown
that its optimal value for a 10 Arms limitation is within
2.0 k
. Pin 3 input has a sensitivity in current which is
limited to reasonable values and should not react to spikes.
If not used, Pin 3 must be connected to a maximum
positive voltage of 5.0 V rather than be left open.
Loop Stability
The Pin 16 network is predominant and must be adjusted
experimentally during module development. The values
indicated in Figure 4 are typical for washing machine
applications but accept large modifications from one model
to another. R16 (the sole restriction) should not go below
33 k, otherwise slew rate limitation will cause large transient
errors for load steps.
Figure 2. Acceleration Ramp
Figure 3. Programmable Double Acceleration Ramp
V
VPin 5
VPin7
t
0
VPin 6 = VDS
VDF = 2 VDS
0
VDS
VDF
High Acceleration
Ramp
Distribution
Low Acceleration
Ramp
High Acceleration
Ramp
VPin5 fixed set value
Speeds
t
VPin4
相關PDF資料 |
PDF描述 |
|---|---|
| TDA1085 | UNIVERSAL MOTOR SPEED CONTROLLER |
| TDA1085C | UNIVERSAL MOTOR SPEED CONTROLLER |
| TDA1085CD | UNIVERSAL MOTOR SPEED CONTROLLER |
| TDA1185A | Triac Phase Angle Controller |
| TDA1512 | 12 TO 20 W HI FI AUDIO POWER AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TDA1085CD | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:UNIVERSAL MOTOR SPEED CONTROLLER |
| TDA1085CG | 功能描述:馬達/運動/點火控制器和驅動器 Universal Motor Speed Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TDA1085CG | 制造商:ON Semiconductor 功能描述:Power Supply IC |
| TDA10H0JB1 | 功能描述:DIP 開關/ SIP 開關 SM HalfPitch DIP Swt SPST, 10 POS, JTerm RoHS:否 制造商:Omron Electronics 位置數量:10 開關類型:DIP 執行器:Rotary 端子節距:2.54 mm 觸點形式: 端接類型:Solder Pin 電流額定值:100 mA 電壓額定值 DC: 工作溫度范圍: 安裝:Through Hole |
| TDA10H0JB1R | 功能描述:DIP 開關/ SIP 開關 SM HalfPitch DIP Swt SPST, 10 POS, JTerm RoHS:否 制造商:Omron Electronics 位置數量:10 開關類型:DIP 執行器:Rotary 端子節距:2.54 mm 觸點形式: 端接類型:Solder Pin 電流額定值:100 mA 電壓額定值 DC: 工作溫度范圍: 安裝:Through Hole |
發布緊急采購，3分鐘左右您將得到回復。