- 您現在的位置：買賣IC網 > PDF目錄361414 > TCM1030P (Power Innovations International, Inc.) DUAL FORWARD-CONDUCTING P-GATE THYRISTORS PROGRAMMABLE OVERVOLTAGE PROTECTORS PDF資料下載
參數資料
| 型號： | TCM1030P |
| 廠商： | Power Innovations International, Inc. |
| 英文描述： | DUAL FORWARD-CONDUCTING P-GATE THYRISTORS PROGRAMMABLE OVERVOLTAGE PROTECTORS |
| 中文描述： | 雙遠期導電的P -可編程門晶閘管過壓保護 |
| 文件頁數： | 7/14頁 |
| 文件大?。?/td> | 286K |
| 代理商： | TCM1030P |
7
SEPTEMBER 1995 - REVISED SEPTEMBER 1997
TISP61060D, TISP61060P
DUAL FORWARD-CONDUCTING P-GATE THYRISTORS
PROGRAMMABLE OVERVOLTAGE PROTECTORS
P R O D U C T I N F O R M A T I O N
thyristor to switch into the low-voltage on-state condition. At the end of the negative half cycle, the thyristor
switches off when the current falls below the holding current value (300 mA). Switch-off and re-clipping at
-52 V causes a second pulse of gate current. The wire current drawn by the protector is quasi-sinusoidal
During the positive a.c. voltage period (diode clipping) there is no gate current. During the negative a.c.
voltage period there are two triangular pulses of gate current, which peak at about 80 mA. This is current
which flows into the gate terminal as indicated by the I
G
current arrow in Figure 2. This direction of current
charges the V
BAT
supply. This would not be a problem if the V
BAT
supply was a rechargeable battery.
However, often the supply is generated from a switching mode power supply or the SLIC supply feed has a
series diode which blocks reverse (charging) current flow to the battery. In these cases the supply can only
sink current in the direction shown by the I
BAT
arrow in Figure 2. Unless the SLIC current, I
SLIC
, is equal or
greater than I
G
the value of V
BAT
will increase, possibly to a level which causes destruction of the SLIC.
The maximum average value of I
G
occurs when the thyristor only clips the voltage and the peak cathode
current is just beginning to approach the switching (I
S
) value, see Figure 4. The average current is maximised
under high source impedance conditions (e.g. 600
). In the case of the LB1201AB, it is recommended that
the supply should be able to absorb 700 mA of “wrong way” current. If the supply cannot absorb the current
then a shunt breakdown diode is recommended to provided a path for the gate current to ground (D2 in
Figure 2). High power diodes are expensive, so diode D2 is usually low power, purposely selected to fail
under this a.c. condition and protect the SLIC.
Figure 3. IC PROTECTOR POWER CROSS WAVE FORMS
Time - ms
0
5
10
15
20
IK
-750
-500
-250
0
250
500
750
IG
-100
-75
-50
-25
0
25
50
75
100
Time - ms
0
5
10
15
20
V
-60
-50
-40
-30
-20
-10
0
10
V
G
V
K
I
K
I
G
AI6XAG
相關PDF資料 |
PDF描述 |
|---|---|
| TCM1060D | DUAL FORWARD-CONDUCTING P-GATE THYRISTORS PROGRAMMABLE OVERVOLTAGE PROTECTORS |
| TCM1060DR | DUAL FORWARD-CONDUCTING P-GATE THYRISTORS PROGRAMMABLE OVERVOLTAGE PROTECTORS |
| TCM1060P | DUAL FORWARD-CONDUCTING P-GATE THYRISTORS PROGRAMMABLE OVERVOLTAGE PROTECTORS |
| TCM1210 | Common Mode Choke Coils for Signal Line |
| TCM1210-201-2P | Common Mode Choke Coils for Signal Line |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TCM1050 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL TRANSIENT-VOLTAGE SUPPRESSORS |
| TCM1050D | 功能描述:TVS二極管陣列 Dual RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C |
| TCM1050DR | 功能描述:TVS二極管陣列 Dual Transient Vltg Suppressor RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C |
| TCM1050P | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL TRANSIENT-VOLTAGE SUPPRESSORS |
| TCM1060 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:DUAL TRANSIENT-VOLTAGE SUPPRESSORS |
發布緊急采購，3分鐘左右您將得到回復。