參數資料
型號: TC74A7-50VCT
廠商: Microchip Technology Inc.
英文描述: Tiny Serial Digital Thermal Sensor
中文描述: 微型串行數字溫度傳感器
文件頁數: 8/16頁
文件大?。?/td> 430K
代理商: TC74A7-50VCT
TC74
DS21462B-page 8
2002 Microchip Technology Inc.
FIGURE 3-1:
SMBUS PROTOCOLS
3.3
START Condition (S)
The TC74 continuously monitors the SDA and SCL
lines for a START condition (a HIGH to LOW transition
of SDA while SCL is HIGH) and will not respond until
this condition is met.
3.4
Address Byte
Immediately following the START Condition, the host
must transmit the address byte to the TC74. The states
of A1 and A0 determine the 7-bit SMBus address for
the TC74. The 7-bit address transmitted in the serial bit
stream must match for the TC74 to respond with an
Acknowledge (indicating the TC74 is on the bus and
ready to accept data). The 8-bit in the Address Byte is
a Read/Write Bit. This bit is a ‘1’ for a read operation or
‘0’ for a write operation. During the first phase of any
transfer this bit will be set = 0 to indicate that the
command byte is being written.
3.5
Acknowledge (ACK)
Acknowledge (ACK) provides a positive handshake
between the host and the TC74. The host releases
SDA after transmitting 8 bits. The host then generates
a ninth clock cycle to allow the TC74 to pull the SDA
line LOW. This action acknowledges that the TC74
successfully received the previous eight bits of data or
address.
3.6
Data Byte
After a successful ACK of the address byte, the host
must transmit the data byte to be written or clock in the
data to be read. (See the appropriate timing diagrams).
ACK will be generated after a successful write of a data
byte into the TC74.
3.7
STOP Condition (P)
Communications must be terminated by a STOP
condition (a LOW to HIGH transition of SDA while SCL
is HIGH). The STOP Condition must be communicated
by the transmitter to the TC74. NOTE: Refer to Timing
Diagrams for serial bus timing.
S
Address
7 Bits
WR
ACK
Command
8 Bits
ACK
Data
ACK
P
8 Bits
Slave Address
Command Byte: selects
which register you are
writing to.
Data Byte: data goes
into the register set
by the command byte.
Write Byte Format
Read Byte Format
S
Address
7 Bits
WR
ACK
Command
8 Bits
ACK
S
Address
RD ACK
Data
NACK
P
7 Bits
8 Bits
Slave Address
Command Byte: selects
which register you are
reading from.
Slave Address: repeated
due to change in data-
flow direction.
Data Byte: reads from
the register set by the
command byte.
Receive Byte Format
S
Address
7 Bits
RD ACK
Data
Nack
P
8 Bits
Data Byte: reads data from
the register commanded by
the last Read Byte or Write
Byte transmission.
S = START Condition
P = STOP Condition
Shaded = Slave Transmission
相關PDF資料
PDF描述
TC74A4-50VAT Tiny Serial Digital Thermal Sensor
TC74A4-50VCT Tiny Serial Digital Thermal Sensor
TC74A3-50VAT Tiny Serial Digital Thermal Sensor
TC74A3-50VCT Tiny Serial Digital Thermal Sensor
TC74A5-50VAT RELAY SWITCH; SMA RELAY SWITCH; FREQUENCY RANGE: DC-18 GHz; SWICH TYPE: TRANSFER; FEATURE: INDICATORS & PULSE LATCHING; ACTUATING VOLTAGE: 28; VSWR: 1.50:1 @ 18 GHz
相關代理商/技術參數
參數描述
TC74AC00F 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:QUAD 2 - INPUT NAND GATE
TC74AC00F(F) 制造商:Toshiba 功能描述:74AC Quad 2-Input NAND Gate 14SOP Bulk 制造商:Toshiba America Electronic Components 功能描述:IC, 74 series logic 制造商:Toshiba 功能描述:NAND Gate 4-Element 2-IN CMOS 14-Pin SOP Tube
TC74AC00F_12 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Quad 2-Input NAND Gate
TC74AC00FN 功能描述:IC GATE NAND QUAD 2INP 14-SOL RoHS:否 類別:集成電路 (IC) >> 邏輯 - 柵極和逆變器 系列:74AC 標準包裝:2,000 系列:74LCX 邏輯類型:逆變器,緩沖器 電路數:1 輸入數:8 特點:三態 電源電壓:2 V ~ 3.6 V 電流 - 靜態(最大值):10µA 輸出電流高,低:24mA,24mA 邏輯電平 - 低:0.7 V ~ 0.8 V 邏輯電平 - 高:1.7 V ~ 2 V 額定電壓和最大 CL 時的最大傳播延遲:6.5ns @ 3.3V,50pF 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 供應商設備封裝:20-SSOP 封裝/外殼:20-SSOP(0.209",5.30mm 寬) 包裝:帶卷 (TR)
TC74AC00FN(ELF,M) 制造商:Toshiba America Electronic Components 功能描述:IC 2-INP NAND GATE QUAD 14-SOL 制造商:Toshiba America Electronic Components 功能描述:IC GATE NAND QUAD 2INP 14-SOL