- 您現在的位置：買賣IC網 > PDF目錄98179 > TC7135C/LI713 1-CH 4-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC28 PDF資料下載
參數資料
| 型號： | TC7135C/LI713 |
| 元件分類： | ADC |
| 英文描述： | 1-CH 4-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC28 |
| 封裝： | PLASTIC, LCC-28 |
| 文件頁數： | 4/28頁 |
| 文件大?。?/td> | 443K |
| 代理商： | TC7135C/LI713 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
TC7135
DS21460D-page 12
2007 Microchip Technology Inc.
6.0
TYPICAL APPLICATIONS
6.1
Component Value Selection
6.1.1
INTEGRATING RESISTOR
The integrating resistor RINT is determined by the full-
scale input voltage and the output current of the buffer
used to charge the integrator capacitor (CINT). Both the
buffer amplifier and the integrator have a class A output
stage, with 100 A of quiescent current. A 20 A drive
current gives negligible linearity errors. Values of 5 A
to 40 A give good results. The exact value of an
integrating resistor for a 20 A current is easily
calculated.
EQUATION 6-1:
6.1.2
INTEGRATING CAPACITOR (CINT)
The product of integrating resistor and capacitor should
be selected to give the maximum voltage swing that
ensures the tolerance build-up will not saturate the
integrator swing (approximately 0.3V from either
supply). For ±5V supplies and ANALOG COMMON tied
to supply ground, a ±3.5V to ±4V full scale integrator
swing
is
adequate.
A
0.10 F
to
0.47 F
is
recommended. In general, the value of CINT is given
by:
EQUATION 6-2:
A very important characteristic of the integrating
capacitor CINT is that it has low dielectric absorption to
prevent rollover or ratiometric errors. A good test for
dielectric absorption is to use the capacitor with the
input tied to the reference. This ratiometric condition
should read half scale 0.9999, with any deviation
probably due to dielectric absorption. Polypropylene
capacitors give undetectable errors at reasonable cost.
Polystyrene and polycarbonate capacitors may also be
used in less critical applications.
6.1.3
AUTO-ZERO AND REFERENCE
CAPACITORS
The size of the auto-zero capacitor has some influence
on the noise of the system, with a larger capacitor
reducing the noise. The reference capacitor should be
large enough such that stray capacitance to ground
from its nodes is negligible.
The dielectric absorption of the reference and auto-
zero capacitors are only important at power-on or when
the circuit is recovering from an overload. Smaller or
cheaper capacitors can be used if accurate readings
are not required for the first few seconds of recovery.
6.1.4
REFERENCE VOLTAGE
The analog input required to generate a full-scale
output is VIN = 2 VREF.
The stability of the reference voltage is a major factor in
the overall absolute accuracy of the converter. For this
reason, it is recommended that a high-quality reference
be used where high-accuracy absolute measurements
are being made.
6.2
Conversion Timing
6.2.1
LINE FREQUENCY REJECTION
A signal integration period at a multiple of the 60 Hz
line frequency will maximize 60 Hz “l(fā)ine noise”
rejection. A 100 kHz clock frequency will reject 50 Hz,
60 Hz and 400 Hz noise. This corresponds to five
TABLE 6-1:
CONVERSION RATE VS.
CLOCK FREQUENCY
R
INT
Full Scale Voltage
20
μA
--------------------------------------------
=
C
INT
10 000
,
clock period
×
[] I
INT
×
integrator output voltage swing
---------------------------------------------------------------------------
=
10 000
,
() clock period
() 20
μA
×
integrator output voltage swing
------------------------------------------------------------------------------
=
Oscillator Frequency
(kHz)
Conversion Rate
(Conv./Sec.)
100
2.5
120
3
200
5
300
7.5
400
10
800
20
1200
30
相關PDF資料 |
PDF描述 |
|---|---|
| TC7135C/KW | 1-CH 4-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP44 |
| TC7135C/BU | 1-CH 4-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP64 |
| TC7135CJI | DUAL-SLOPE ADC, PARALLEL ACCESS, CDIP28 |
| TC7135CLI | DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC28 |
| TC7135CPI | DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC7135CPI | 功能描述:LED顯示驅動器 4-1/2 Digit A/D BCD RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| TC7135CPL | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:4-1/2 Digit A/D Converter |
| TC7136 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low Power 3-1/2 Digit Analog-to-Digital Converter |
| TC7136A | 制造商:TELCOM 制造商全稱:TelCom Semiconductor, Inc 功能描述:LOW POWER, 3-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTERS |
| TC7136ACKW | 功能描述:LCD 驅動器 Low Power RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。