參數資料
型號： TC7135C/LI713
元件分類： ADC
英文描述： 1-CH 4-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC28
封裝： PLASTIC, LCC-28
文件頁數： 3/28頁
文件大小： 443K
代理商： TC7135C/LI713
2007 Microchip Technology Inc.
DS21460D-page 11
TC7135
5.3
BUSY Output
At the beginning of the signal integration phase, BUSY
goes high and remains high until the first clock pulse
after the integrator zero crossing. BUSY returns to the
logic ‘0’ state once the measurement cycle ends in an
overrange condition. The internal display latches are
loaded during the first clock pulse after BUSY and are
latched at the clock pulse end. The BUSY signal does
not go high at the beginning of the measurement cycle,
which starts with the auto-zero cycle.
5.4
OVERRANGE Output
If the input signal causes the reference voltage integra-
tion time to exceed 20,000 clock pulses, the OVER-
RANGE output is set to a logic ‘1’. The OVERRANGE
output register is set when BUSY goes low and is reset
at the beginning of the next reference integration
phase.
5.5
UNDERRANGE Output
If the output count is 9% of full scale or less (-1800
counts), the UNDERRANGE register bit is set at the
end of BUSY. The bit is set low at the next signal
integration phase.
5.6
POLARITY Output
A positive input is registered by a logic ‘1’ polarity
signal. The polarity bit is valid at the beginning of
reference integrate and remains valid until determined
during the next conversion.
The polarity bit is valid even for a zero reading. Signals
less than the converter's LSB will have the signal
polarity determined correctly. This is useful in null
applications.
5.7
Digit Drive Outputs
Digit drive signals are positive-going signals. The scan
sequence is D5 to D1. All positive pulses are 200 clock
pulses wide, with the exception D5, which is 201 clock
pulses wide.
All five digits are scanned continuously, unless an
overrange condition occurs. In an overrange condition,
all digit drives are held low from the final STROBE
pulse until the beginning of the next reference integrate
phase. The scanning sequence is then repeated. This
provides a blinking visual display indication.
5.8
BCD Data Outputs
The binary coded decimal (BCD) bits B8, B4, B2 and B1
are positive-true logic signals. The data bits become
active at the same time as the digit drive signals. In an
overrange condition, all data bits are at a logic ‘0’ state.
相關PDF資料
PDF描述
TC7135C/KW 1-CH 4-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP44
TC7135C/BU 1-CH 4-BIT DUAL-SLOPE ADC, PARALLEL ACCESS, PQFP64
TC7135CJI DUAL-SLOPE ADC, PARALLEL ACCESS, CDIP28
TC7135CLI DUAL-SLOPE ADC, PARALLEL ACCESS, PQCC28
TC7135CPI DUAL-SLOPE ADC, PARALLEL ACCESS, PDIP28
相關代理商/技術參數
參數描述
TC7135CPI 功能描述:LED顯示驅動器 4-1/2 Digit A/D BCD RoHS:否 制造商:Micrel 數位數量:5 片段數量: 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-44 工作電源電壓:4.75 V to 11 V 最大電源電流:10 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube
TC7135CPL 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:4-1/2 Digit A/D Converter
TC7136 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Low Power 3-1/2 Digit Analog-to-Digital Converter
TC7136A 制造商:TELCOM 制造商全稱:TelCom Semiconductor, Inc 功能描述:LOW POWER, 3-1/2 DIGIT ANALOG-TO-DIGITAL CONVERTERS
TC7136ACKW 功能描述:LCD 驅動器 Low Power RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*