- 您現在的位置：買賣IC網 > PDF目錄385904 > TC6387XB (Toshiba Corporation) SD Memory Card / SDIO Card Controller PDF資料下載
參數資料
| 型號： | TC6387XB |
| 廠商： | Toshiba Corporation |
| 英文描述： | SD Memory Card / SDIO Card Controller |
| 中文描述： | SD卡/ SDIO卡控制器 |
| 文件頁數： | 17/62頁 |
| 文件大小： | 1406K |
| 代理商： | TC6387XB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
TC6387XB Specification
Rev. 1.0 02/02/06
TOTAL
62
PAGE NO.17
TOSHIBA CONFIDENTIAL
4.5 Interruption
When the TC6387XB detects the each interrupt sources, TC6387XB asserts interrupt signals (#HINT). It is necessary
that the interrupt mask bits are released. This mask bits releasing is controlled by setting SD Interrupt Mask
Register(Offset:020-023h, 120-123h). Each factor of the interrupt can be evaluated by referring to SD Card Status
Register(Offset:01C-01Dh, 11C-11Dh) or SD Buffer Control & Error Status Register(Offset:01E-01Fh, 11E-11Fh).
The details of each factor are listed below.
4.5.1 SD card insertion interrupt by #SDCD
+ Interrupt Assert Condition
When an SD card is inserted to a slot, #SDCD is lowered. This condition causes an interrupt to be generated.
#SDCD is not recognized as being lowered unless it remains in "0" state for the number of HCLK cycles specified
by CDM[1:0] of Card Detect Mode Register(Config Offset:4Ch). The interrupt is asserted in th timing of raising of
CLK32 from #SDCD low state.
+ Factor Evaluation Method
The SCIN bit(D4) of SD Card Status Register(Offset:01C-01Dh) is set to "1".
+De-asserting Method
(1) "0" is written into the SCIN bit(D4) of SD Card Status Register(Offset:01C-01Dh).
(2) "1" is written into the MCIN bit(D4) of SD Interrupt Mask Register(Offset:020-023h).
(3) Hardware reset by #PCLR = “0”.
(4) Software reset by writing "0" into the SRST bit(D0) of SD Software Reset Register(Offset:0E0h).
4.5.2 SD card removal interrupt by #SDCD
+ Interrupt Assert Condition
When an SD card in a slot is removed, #SDCD is raised. This condition causes an interrupt to be generated. After
#SDCD is high, the interrupt is asserted in th timing of raising of CLK32.
HCLK
CLK32
#SDCD
#HINT
CDM
相關PDF資料 |
PDF描述 |
|---|---|
| TC652 | Integrated Temperature Sensor & Brushless DC Fan Controller with FanSense⑩Detect & Over-Temperature |
| TC653 | Integrated Temperature Sensor & Brushless DC Fan Controller with FanSense⑩Detect & Over-Temperature |
| TC74AC00FT | QUAD 2 - INPUT NAND GATE |
| TC74AC00P | QUAD 2 - INPUT NAND GATE |
| TC74AC04F | Hex Inverter(高速CMOS六反相器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC6393XB | 制造商:Toshiba America Electronic Components 功能描述:SECURE DIGITAL HOST CONTROLLER - Tape and Reel |
| TC6-3E25 | 制造商:FERROXCUBE 制造商全稱:Ferroxcube International Holding B.V. 功能描述:Ferrite toroids |
| TC6-3E5 | 制造商:FERROXCUBE 制造商全稱:Ferroxcube International Holding B.V. 功能描述:Ferrite toroids |
| TC6-3E6 | 制造商:FERROXCUBE 制造商全稱:Ferroxcube International Holding B.V. 功能描述:Ferrite toroids |
| TC6-3F3 | 制造商:FERROXCUBE 制造商全稱:Ferroxcube International Holding B.V. 功能描述:Ferrite toroids |
發布緊急采購，3分鐘左右您將得到回復。