- 您現在的位置：買賣IC網 > PDF目錄98169 > TC2575-12.0VAT 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PSFM5 PDF資料下載
參數資料
| 型號： | TC2575-12.0VAT |
| 元件分類： | 穩壓器 |
| 英文描述： | 3.2 A SWITCHING REGULATOR, 63 kHz SWITCHING FREQ-MAX, PSFM5 |
| 封裝： | TO-220, 5 PIN |
| 文件頁數： | 26/26頁 |
| 文件大?。?/td> | 172K |
| 代理商： | TC2575-12.0VAT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁
9
TC2575
TC2575-1 3/13/00
1.0A Step-Down Switching Regulator
2001 Microchip Technology Inc.
DS21398A
Procedure (Adjustable Output Version: TC2575-ADJ) (Continued)
Procedure
Example
3. Catch Diode Selection (D1)
A. Since the diode maximum peak current exceeds the
regulator maximum load current the catch diode current
rating must be at least 1.2 times greater than the
maximum load current. For a robust design, the diode
should have a current rating equal to the maximum
current limit of the TC2575 to be able to with stand a
continuous output short.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
4. Inductor Selection (L1)
A. Use the following formula to calculate the inductor
Volt x microsecond [V x
s] constant:
E x T = ( VIN – VOUT)
VOUT
x
10
6
[V x
sec]
VIN
F[Hz]
B. Match the calculated E x T value with the corresponding
number on the vertical axis of the Inductor Value
Selection Guide shown in Figure 37. This E x T constant
is a measure of the energy handling capability of an
inductor and is dependent upon the type of core, the core
area, the number of turns, and the duty cycle.
C. Next step is to identify the inductance region intersected
by the E x T value and the maximum load current value
on the horizontal axis shown in Figure 35.
D. From the inductor code, identify the inductor value. Then
select an appropriate inductor from Table 1 or Table 2.
The inductor chosen must be rated for a switching
frequency of 52kHz and for a current rating of 1.15 x
ILOAD . The inductor current rating can also be deter-
mined by calculating the inductor peak current:
IP (max) = ILOAD(max) +
(VIN – VOUT) tON
2L
where tON is the "on" time of the power switch and
tON =
(VOUT
x
1.0 )
VIN
fOSC
For additional information about the inductor, see
the inductor section in the “External Components”
section of this data sheet.
3. Catch Diode Selection (D1)
A. For this example, a 3.0A current rating is adequate.
B. Use a 20V IN5820 or MBR320 Schottky diode or any
suggested fast recovery diodes in Table 4.
4. Inductor Selection (L1)
A. Calculate E x T [V x
sec] constant:
E x T = ( 12 – 8.0) x
8.0
x
1000
= 51[V x
sec]
12
52
B. E x T = 51 [V x
sec]
C. ILOAD(max) = 1.0A
Inductance Region = L220
D. Proper inductor value = 220
H
Choose the inductor from Table 1 or Table 2
相關PDF資料 |
PDF描述 |
|---|---|
| TC271-40 | SPECIALTY ANALOG CIRCUIT, CDIP22 |
| TC33025VOETR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TC33163EOETR | 3.4 A SWITCHING CONTROLLER, 55 kHz SWITCHING FREQ-MAX, PDSO16 |
| TC33163EOETR | 3.4 A SWITCHING REGULATOR, 55 kHz SWITCHING FREQ-MAX, PDSO16 |
| TC3400VOART | 2-CH 16-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC2575-3.3VAT | 制造商:TELCOM 制造商全稱:TelCom Semiconductor, Inc 功能描述:1.0A Step-Down Switching Regulator |
| TC2575-5.0VAT | 制造商:TELCOM 制造商全稱:TelCom Semiconductor, Inc 功能描述:1.0A Step-Down Switching Regulator |
| TC2575VAT | 制造商:TELCOM 制造商全稱:TelCom Semiconductor, Inc 功能描述:1.0A Step-Down Switching Regulator |
| TC258 | 制造商:MCM 功能描述:6FT DC POWER CORD STRAIGHT 2.5X5.5 18 AWG |
| TC258B | 制造商:Datak Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。