
TC2014/2015/2185
DS21662C-page 2
2003 Microchip Technology Inc.
1.0
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings
Input Voltage ................................................................... 6.5V
Output Voltage ....................................... (– 0.3) to (V
IN
+ 0.3)
Operating Temperature ......................... – 40°C < T
J
< 125°C
Storage Temperature ................................. – 65°C to +150°C
Maximum Voltage on Any Pin ................ V
IN
+0.3V to – 0.3V
Maximum Junction Temperature.................................. 150°C
Notice:
Stresses above those listed under "Maximum
Ratings" may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operation listings of this specification is not implied. Exposure
to maximum rating conditions for extended periods may affect
device reliability.
ELECTRICAL CHARACTERISTICS
PIN FUNCTION TABLE
Name
Function
V
IN
GND
SHDN
Bypass
V
OUT
Unregulated Supply Input
Ground Terminal
Shutdown Control Input
Reference Bypass Input
Regulated Voltage Output
Electrical Specifications:
Unless otherwise specified, V
IN
= V
R
+ 1V, I
L
= 100 μA, C
OUT
= 3.3 μF, SHDN > V
IH
, T
A
= +25°C.
BOLDFACE
type specifications apply for junction temperature of -40°C to +125°C.
Parameters
Sym
Min
Typ
Max
Units
Conditions
Input Operating Voltage
V
IN
2.7
—
6.0
V
Note 1
Maximum Output
Current
I
OUTMAX
50
—
—
mA
TC2014
100
—
—
TC2015
150
—
—
TC2185
Output Voltage
V
OUT
TCV
OUT
V
R
- 2.0%
—
V
R
± 0.4%
20
V
R
+ 2.0%
—
V
Note 2
V
OUT
Temperature
Coefficient
ppm/°C
Note 3
—
40
—
Line Regulation
V
OUT
/
V
IN
V
OUT
/V
OUT
—
0.05
0.5
%
(V
R
+ 1V) < V
IN
< 6V
TC2014;TC2015: I
L
= 0.1 mA to I
OUTMAX
TC2185: I
L
= 0.1 mA to I
OUTMAX
Note 4
Note 5
I
L
= 100 μA
I
L
= 50 mA
TC2015; TC2185
I
L
= 100 mA
TC2185
I
L
= 150 mA
SHDN = V
IH
, I
L
=0
SHDN = 0V
Load Regulation
(Note 4)
-1.0
0.33
+1.0
%
-2.0
0.43
+2.0
Dropout Voltage
V
IN
- V
OUT
—
2
—
mV
—
45
70
—
90
140
—
140
210
Supply Current
I
IN
—
55
80
μA
Shutdown Supply
Current
I
INSD
—
0.05
0.5
μA
Note
1:
2:
3:
The minimum V
IN
has to meet two conditions: V
IN
= 2.7V and V
IN
= V
R
+ V
DROPOUT
.
V
R
is the regulator output voltage setting. For example: V
R
= 1.8V, 2.7V, 2.8V, 2.85V, 3.0V, 3.3V.
4:
Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested
over a load range from 1.0 mA to the maximum specified output current. Changes in output voltage due to heating
effects are covered by the thermal regulation specification.
Dropout voltage is defined as the input-to-output differential at which the output voltage drops 2% below its nominal
value at a V differential.
Thermal Regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied,
excluding load or line regulation effects. Specifications are for a current pulse equal to I
MAX
at V
IN
= 6V for T = 10 msec.
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction tem-
perature and the thermal resistance from junction-to-air (i.e. T
A
, T
J
,
θ
JA
).
Time required for V
OUT
to reach 95% of V
R
(output voltage setting), after V
SHDN
is switched from 0 to V
IN
.
5:
6:
7:
8:
TCV
OUT
V
-----------------------V
V
OUT
×
–
(
)
106
–
×
T
=