- 您現在的位置：買賣IC網 > PDF目錄384950 > TC1276 (Microchip Technology Inc.) 3-Pin Reset Monitors for 3.3V Systems PDF資料下載
參數資料
| 型號： | TC1276 |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | 3-Pin Reset Monitors for 3.3V Systems |
| 中文描述： | 3引腳復位監控器為3.3V系統 |
| 文件頁數： | 5/13頁 |
| 文件大?。?/td> | 469K |
| 代理商： | TC1276 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁
2002 Microchip Technology Inc.
DS21383B-page 5
TC1275/TC1276/TC1277
3.2
V
CC
Transient Rejection
The TC1275/TC1276/TC1277 provides accurate V
CC
monitoring and reset timing during power-up, power-
down, and brownout/sag conditions, and rejects
negative-going transients (glitches) on the power
supply line. Figure 3-5 shows the maximum transient
duration vs. maximum negative excursion (overdrive)
for glitch rejection. Any combination of duration and
overdrive that lays
under
the curve will
not
generate a
reset signal. Combinations above the curve are
detected as a brownout or power-down. Transient
immunity can be improved by adding a capacitor in
close proximity to the V
CC
pin of the TC1275/TC1276/
TC1277.
3.3
RESET Signal Integrity During
Power-Down
The TC1275 RESET output is valid to V
CC
= 1.2V.
Below this voltage the output becomes an "open
circuit" and does not sink current. This means CMOS
logic inputs to the
μ
P will be floating at an undeter-
mined voltage. Most digital systems are completely
shut down well above this voltage. However, in situa-
tions where RESET must be maintained valid to V
CC
=
0V, a pull-down resistor must be connected from
RESET to ground to discharge stray capacitances and
hold the output low (Figure 3-6). This resistor value,
though not critical, should be chosen such that it does
not appreciably load RESET under normal operation
(100k
will be suitable for most applications). Similarly,
a pull-up resistor to V
CC
is required for the TC1277 to
ensure a valid high RESET for V
CC
below 1.8V.
FIGURE 3-5:
MAXIMUM TRANSIENT
DURATION VS.
OVERDRIVE FOR GLITCH
REJECTION AT 25°C
FIGURE 3-6:
ENSURING RESET VALID
TO V
CC
= 0V
RESET COMPARATOR OVERDRIVE,
[
V
CCTP
- V
CC
]
(mV)
500
300
200
400
100
0
1
10
100
1000
μ
s
T
A
°
C
V
TH
Duration
Overdrive
V
CC
TC1275/6/7
TC1275
V
CC
V
CC
R1
100k
RESET
GND
相關PDF資料 |
PDF描述 |
|---|---|
| TC1277 | 3-Pin Reset Monitors for 3.3V Systems |
| TC1300H | SURFACE MOUNT THYRISTOR SURGE PROTECTIVE DEVICE |
| TC0900H | SURFACE MOUNT THYRISTOR SURGE PROTECTIVE DEVICE |
| TC1800H | SURFACE MOUNT THYRISTOR SURGE PROTECTIVE DEVICE |
| TC1500H | SURFACE MOUNT THYRISTOR SURGE PROTECTIVE DEVICE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TC1276-10ENB | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:3-Pin Reset Monitors for 3.3V Systems |
| TC1276-10ENBTR | 功能描述:監控電路 3-Pin for 3.3V Syst RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| TC1276-15ENB | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:3-Pin Reset Monitors for 3.3V Systems |
| TC1276-20ENBTR | 功能描述:監控電路 3-Pin for 3.3V Syst RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| TC1276-5ENB | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:3-Pin Reset Monitors for 3.3V Systems |
發布緊急采購，3分鐘左右您將得到回復。