- 您現在的位置：買賣IC網 > PDF目錄225279 > TB6608FNG STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 PDF資料下載
參數資料
| 型號： | TB6608FNG |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 |
| 封裝： | 0.225 INCH, 0.65 MM PITCH, PLASTIC, SSOP-20 |
| 文件頁數： | 6/30頁 |
| 文件大?。?/td> | 356K |
| 代理商： | TB6608FNG |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
TB6608FNG
2007-12-17
14
Chopper Control
Turning on the power (chop on) causes a current to flow into the coils. Once the VRF voltage reaches Vref, it is
detected by the comparator and the power is turned off (chop off).
The off timer/counter counts the number of falling edges of the internal CK signal, which is derived from the OSC
signal, and generates the motor-driving PWM signal based on the turn-off time of four CK cycles.
The upper limit of the current across the motor coil (i.e., the peak current in each excitation mode), I (Limit), can
be calculated as follows:
I (Limit)
= Vref/RNF
Vref equals to 0.125 V when TQ is Low, while it equals to 0.5 V when TQ is High.
RNF is the value of resistors used for output current detection. One of those resistors is connected between RFA
and GND, and the other is connected between RFB and GND.
Timing chart may be simplified for the sake of brevity.
Internal CK
OSC
Off timer counter
Upper limit:
Vref/RNF
Coil current
chop on
off
on
off
on
off
on
Generate PWM
相關PDF資料 |
PDF描述 |
|---|---|
| TBS22A | SINGLE COLOR LED |
| TBT4854 | Pigtailed PD for analog application |
| TBT4855 | Pigtailed PD for analog application |
| TBT4856 | Pigtailed PD for analog application |
| TBT48N3 | Pigtailed PD for analog application |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB6608FNG(C8,EL,HJ | 制造商:Toshiba 功能描述:Cut Tape 制造商:Toshiba America Electronic Components 功能描述:2ph stepping motor driver 制造商:Toshiba 功能描述:Stepper Motor Driver 3.3V T/R |
| TB6608FNG(C8OEL,HZ | 功能描述:馬達/運動/點火控制器和驅動器 2-phase stepping motor Drvr 15V RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6608FNG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6612FNG(O,C,8,EL | 功能描述:馬達/運動/點火控制器和驅動器 15V Bridge Drvr for brushed DC motors RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6612FNG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 Bridge Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。