- 您現在的位置：買賣IC網 > PDF目錄225279 > TB6608FNG STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 PDF資料下載
參數資料
| 型號： | TB6608FNG |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO20 |
| 封裝： | 0.225 INCH, 0.65 MM PITCH, PLASTIC, SSOP-20 |
| 文件頁數： | 19/30頁 |
| 文件大?。?/td> | 356K |
| 代理商： | TB6608FNG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
TB6608FNG
2007-12-17
26
Application Circuit Example
Note 1: Capacitors for the power supply lines should be connected as close to the IC as possible.
Note 2: The STBY pin must be set Low upon powering on and off the device. Otherwise, a large current might
abruptly flow through the output pins.
Also, at the power-on, VM must be applied after applying VCC. At the power-off, VCC must be turned off after
turning off VM.
Usage Considerations
A large current might abruptly flow through the IC in case of a short-circuit across its outputs, a short-circuit to
power supply or a short-circuit to ground, leading to a damage of the IC. Also, the IC or peripheral parts may be
permanently damaged or emit smoke or fire resulting in injury especially if a power supply pin (VCC, VM) or an
output pin (AO1, AO2, BO1, BO2) is short-circuited to adjacent or any other pins.
These possibilities should be fully considered in the design of the output, VCC, VM and ground lines.
Install this IC correctly. If not, (e.g., installing it in the wrong position,) the IC may be damaged permanently.
Fuses should be connected to the power supply lines.
0.1
μF
47
μF
VCC = 3.3 V
Clock
CW/CCW
Reset
Enable
Standby
H/L
220
pF
VCC
MO
CK
CW/CCW
RESET
ENABLE
STBY
M1
M2
DCY
TQ
OSC
0.1
μF
47
μF
VM = 5 V
VM
AO1
AO2
CPU
I/O
BO1
BO2
RFA
RFB
Stepping
Motor
2
Ω
2
Ω
GND
TB6608FNG
相關PDF資料 |
PDF描述 |
|---|---|
| TBS22A | SINGLE COLOR LED |
| TBT4854 | Pigtailed PD for analog application |
| TBT4855 | Pigtailed PD for analog application |
| TBT4856 | Pigtailed PD for analog application |
| TBT48N3 | Pigtailed PD for analog application |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB6608FNG(C8,EL,HJ | 制造商:Toshiba 功能描述:Cut Tape 制造商:Toshiba America Electronic Components 功能描述:2ph stepping motor driver 制造商:Toshiba 功能描述:Stepper Motor Driver 3.3V T/R |
| TB6608FNG(C8OEL,HZ | 功能描述:馬達/運動/點火控制器和驅動器 2-phase stepping motor Drvr 15V RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6608FNG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6612FNG(O,C,8,EL | 功能描述:馬達/運動/點火控制器和驅動器 15V Bridge Drvr for brushed DC motors RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6612FNG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 Bridge Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。