- 您現在的位置：買賣IC網 > PDF目錄98167 > TB6582FG BRUSHLESS DC MOTOR CONTROLLER, 0.002 A, PQFP52 PDF資料下載
參數資料
| 型號： | TB6582FG |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.002 A, PQFP52 |
| 封裝： | 10 X 10 MM, 0.65 MM PITCH, ROHS COMPLIANT, PLASTIC, QFP-52 |
| 文件頁數： | 3/28頁 |
| 文件大?。?/td> | 279K |
| 代理商： | TB6582FG |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
TB6582FG
2007-10-18
Design Specifications
11
(a)
DC excitation time
Duty cycle is determined by the gradient of SC terminal voltage, which depends on the charging of a
capacitor.
This voltage is clamped when the output duty cycle reaches about 35
% for the de-excitation and
over-current protection.
When CW
= U-phase → V-phase
When CCW
= U-phase → W-phase
Ta (typ.)
= 2.3 × CIP × RST (s)
(b)
Forced commutation time
The forced commutation is started when the IP pin voltage falls below to 0.5 V or lower.
The output duty cycle of forced commutation is determined by VSP input voltage.
FST = High
: Forced commutation frequency fST = fosc/(6 × 217)
FST = Middle
: Forced commutation frequency fST = fosc/(6 × 218)
FST = Low
: Forced commutation frequency fST = fosc/(6 × 219)
Example) When fOSC = 5 MHz,
FST = High
: fST 6.4 (Hz)
FST = Middle : fST 3.2 (Hz)
FST = Low or Open : fST 1.6 (Hz)
The rotor is aligned to a certain position specified in DC excitation mode for the period of (a), during which
the IP pin voltage decreases from Vrefout to 0.5 V. The time constant for the period is determined by CIP
and RST. After that, operation mode is switched to forced commutation mode (b) as shown above. The duty
cycle for DC excitation mode is determined according to the SC pin voltage. And after the IP pin voltage
falls to 0.5 V or lower, the duty cycle is determined according to the VSP pin voltage. When the rotational
frequency exceeds the forced commutation frequency specified with the status of the FST pin, the operation
mode is switched to the sensorless square-wave mode.
Preliminary
相關PDF資料 |
PDF描述 |
|---|---|
| TB6592FLG | BRUSH DC MOTOR CONTROLLER, 0.8 A, PQCC24 |
| TB6595FL | BRUSH DC MOTOR CONTROLLER, 0.8 A, PQCC36 |
| TB6598FN | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO16 |
| TB6607FLG | STEPPER MOTOR CONTROLLER, 0.8 A, PQCC36 |
| TB6615PG | STEPPER MOTOR CONTROLLER, PDIP16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB6582FG(ES) | 制造商:Toshiba America Electronic Components 功能描述: |
| TB6582FG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 Brushless DC Motor Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6582FG(OEL) | 制造商:Toshiba America Electronic Components 功能描述:BRUSHLESS DC MOTOR DRIVER 18V 0.2MA |
| TB6584AFNG(O,C8,EL | 功能描述:馬達/運動/點火控制器和驅動器 Brushless Motor DRVR 3-Phase 1A 45V RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6584AFNG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Brushless Driver IC 45V 1.8A RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。