- 您現在的位置：買賣IC網 > PDF目錄98167 > TB6582FG BRUSHLESS DC MOTOR CONTROLLER, 0.002 A, PQFP52 PDF資料下載
參數資料
| 型號： | TB6582FG |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 0.002 A, PQFP52 |
| 封裝： | 10 X 10 MM, 0.65 MM PITCH, ROHS COMPLIANT, PLASTIC, QFP-52 |
| 文件頁數： | 22/28頁 |
| 文件大小： | 279K |
| 代理商： | TB6582FG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁
TB6582FG
2007-10-18
Design Specifications
3
External Parts
Symbol
Function
Recommended Value
Remarks
OSC/C
390 pF
OSC/R
Reference clock generation
(5 MHz)
6.8 k
(Note 1)
CSC
3.3
F (0.47 to 4.7 F)
RST
220 k
CIP
DC excitation setting
4.7
F
(Note 2)
CREF
Vrefout oscillation prevention
(0.1
F)
CVCC
VCC power supply stabilization
25 V/1
F
(Note 3)
R1
Phase current detection
0.33
(Note 4)
R2
201 k
R3
Motor reference detection
1 k
(Note 5)
R4
200 k
R5
Induced voltage detection
2 k
(Note 6)
R6
360 k
R7
11 k
C1
0.012
F
C2
Motor constant setting
0.15
F
(Note 7)
R8
91 k
R9
91 k
C3
0.015 pF
C4
Two-stage low-pass filter
0.0039
F
(Note 8)
CLA
Lead angle adjustment
(0.022
F)
(Note 9)
Note 1: These values determine the internal IC reference clock. Recommended values are required to be used for
external capacitor and resister in setting the carrier frequency at 20 KHz.
Note 2: These are used to determine the DC excitation time and duty cycle at startup. Since those required time and
duty cycle vary depending on the motor type, appropiate values must be determined through experiments.
Since the motor is driven by a minimum current, these must be connected as close as possible to the IC
lead.
Note 3: These capacitors are used for power supply stabilization. Appropriate values must be determined depending
on usage environment. These capacitors must also be connected as close as possible to the IC lead to
enhance noise rejection.
Note 4: The voltage generated at the phase current detection resistor R1 must be below 0.5 V.
Note 5: R2 and R3 should be adjusted so that the voltages generated at those resistors become half the voltages
generated at the induced voltage detection resistors, R4 and R5, respectively. Since these voltages are also
used for VM-power supply monitoring, ensure that VCC does not exceed the operating power-supply voltage
range. For a detailed functional description, refer to the functional description in Section 16, VCC-Power
Supply Monitoring.
Note 6: These resistors are used for the induced voltage detection in square-wave mode. Also, these resistors are
used for the detection of the voltage applied to the motor in sine-wave mode. R4 and R5 should be adjusted
so that the voltage applied to the TB6582FG becomes 4.5 V or lower.
Note 7: The time constant varies depending on the inductance and resistance of each motor. Thus, attach the motor
to the TB6582 and adjust the time constant experimentally. For more details, refer to the functional
description in Section 7, Induced Voltage Detection.
Note 8: The PWM signals generated from the output pins must be low-pass filtered to obtain linear voltages.
Note 9: This capacitor is used to specify the lead angle in sine-wave mode. For the automatic lead-angle correction,
the appropriate CLA should be used so that the U-phase current is delayed by the amount of time obtained
based on the calculated induced voltage. For more details, refer to the functional description in Section 8,
Lead Angle Correction.
Preliminary
相關PDF資料 |
PDF描述 |
|---|---|
| TB6592FLG | BRUSH DC MOTOR CONTROLLER, 0.8 A, PQCC24 |
| TB6595FL | BRUSH DC MOTOR CONTROLLER, 0.8 A, PQCC36 |
| TB6598FN | STEPPER MOTOR CONTROLLER, 0.8 A, PDSO16 |
| TB6607FLG | STEPPER MOTOR CONTROLLER, 0.8 A, PQCC36 |
| TB6615PG | STEPPER MOTOR CONTROLLER, PDIP16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB6582FG(ES) | 制造商:Toshiba America Electronic Components 功能描述: |
| TB6582FG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 Brushless DC Motor Controller RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6582FG(OEL) | 制造商:Toshiba America Electronic Components 功能描述:BRUSHLESS DC MOTOR DRIVER 18V 0.2MA |
| TB6584AFNG(O,C8,EL | 功能描述:馬達/運動/點火控制器和驅動器 Brushless Motor DRVR 3-Phase 1A 45V RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6584AFNG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 3-Phase Brushless Driver IC 45V 1.8A RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。