- 您現在的位置：買賣IC網 > PDF目錄98167 > TB6549F BRUSH DC MOTOR CONTROLLER, 3.5 A, PDSO20 PDF資料下載
參數資料
| 型號： | TB6549F |
| 元件分類： | 運動控制電子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 3.5 A, PDSO20 |
| 封裝： | 0.450 INCH, 1 MM PITCH, PLASTIC, HSOP-20/22 |
| 文件頁數： | 20/22頁 |
| 文件大?。?/td> | 398K |
| 代理商： | TB6549F |
TB6549F/FG/P/PG/HQ
2006-11-07
7
Note: Be sure to set the pin PWM to High when the PWM control function is not used.
2.
Standby Circuit
All circuits are turned off except the standby circuit and the charge pump circuit under the standby
condition.
The input voltage range is shown below. Input at CMOS and TTL level is possible. The input signal has
0.2 V (typ.) hysteresis.
VINSH: 2 to Vreg V
VINSL: GND to 0.8 V
Do not attempt to the control the output by inputting PWM signals to the standby pin. Doing so may
cause the output signal to become unstable, resulting in destruction of the IC.
The charge pump circuit is turned ON/OFF by the switch of the input signal from the standby pin. If
the switching cycle is shorter than 50 ms, the charge pump circuit will not operate with precise timing.
Therefore the switching cycle of the standby pin should be longer than 50 ms.
When the Standby condition is changed to Operation Mode, set IN1 and IN2 to Low level (Stop Mode) at
first. Then switch IN1 and IN2 to High level when the charge pump circuit reaches the stable condition,
i.e., when VcpA is about VCC + 5 V.
VCC
M
GND
VCC
M
GND
PWM ON
t5
PWM OFF
→ ON
t4
= 300 ns (typ.)
VCC
M
GND
PWM OFF
t3
PWM ON
→ OFF
t2
= 300 ns (typ.)
VCC
M
GND
VCC
M
GND
PWM ON
t1
OUT1
t2
GND
VCC
Output Voltage Waveform
(OUT1)
t1
t3
t5
t4
VDD
100 k
SB
相關PDF資料 |
PDF描述 |
|---|---|
| TB6549HQ | BRUSH DC MOTOR CONTROLLER, 5 A, ZIP25 |
| TB6551FAG | BRUSHLESS DC MOTOR CONTROLLER, PDSO24 |
| TB6552FL | BRUSH DC MOTOR CONTROLLER, 1 A, PQCC24 |
| TB6552FN | BRUSH DC MOTOR CONTROLLER, 1 A, PDSO16 |
| TB6559FG | BRUSH DC MOTOR CONTROLLER, 2.5 A, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB6549F_07 | 制造商:TOSHIBA 制造商全稱:Toshiba Semiconductor 功能描述:Full-Bridge Driver IC for DC Motors |
| TB6549FG | 制造商:Toshiba 功能描述:Full Bridge Motor Driver 22-Pin (20+2Tab) HSOP Bulk 制造商:Toshiba America Electronic Components 功能描述:DRIVER FULL BRIDGE SMD HSOP20 制造商:Toshiba America Electronic Components 功能描述:DRIVER, FULL BRIDGE, SMD, HSOP20 |
| TB6549FG(EL) | 功能描述:馬達/運動/點火控制器和驅動器 Bridge Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB6549FG(O) | 制造商:Toshiba America Electronic Components 功能描述:Moter Driver,Full Brdg Driver,HSOP20 |
| TB6549FG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 Bridge Driver 30V 3.5A 4 modes RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。