- 您現在的位置：買賣IC網 > PDF目錄385899 > TB62206FG (Toshiba Corporation) BiCD PWM 2−Phase Bipolar Stepping Motor Driver PDF資料下載
參數資料
| 型號： | TB62206FG |
| 廠商： | Toshiba Corporation |
| 英文描述： | BiCD PWM 2−Phase Bipolar Stepping Motor Driver |
| 文件頁數： | 13/27頁 |
| 文件大?。?/td> | 369K |
| 代理商： | TB62206FG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
TB62206FG
2005-03-02
13
Power Supply Sequence
(recommended)
Note 1: If the V
DD
drops to the level of the V
DDR
or below while the specified voltage is input to the V
M
pin, the IC is
internally reset.
This is a protective measure against malfunction. Likewise, if the V
M
drops to the level of the V
MR
or below
while regulation voltage is input to the V
DD
, the IC is internally reset as a protective measure against
malfunction.
To avoid malfunction, when turning on V
M
or V
DD
, to input the STANDBY signal at the above timing is
recommended.
It takes time for the output control charge pump circuit to stabilize. Wait up to t
ONG
time after power on
before driving the motors.
Note 2: When the V
M
value is between 8 to 11 V, the internal reset is released, thus output may be on. In such a
case, the charge pump cannot drive stably because of insufficient voltage. The Standby state should be
maintained until V
M
reaches 13 V or more.
Note 3: Since V
DD
=
0 V and V
M
=
voltage within the rating are applied, output is turned off by internal reset.
At that time, a current of several mA flows due to the Pass between V
M
and V
DD
.
When voltage increases on V
DD
output, make sure that specified voltage is input.
V
DD (max)
V
DD (min)
V
DDR
GND
V
DD
V
M
V
M (min)
V
MR
GND
V
M
Active
Non-active
Internal operable
H
L
STANDBY
INPUT (Note 1)
Takes up to t
ONG
until operable.
Non-operable area
STANDBY
相關PDF資料 |
PDF描述 |
|---|---|
| TB62209FG | Stepping Motor Driver IC Using PWM Chopper Type |
| TB62209F | Stepping Motor Driver IC Using PWM Chopper Type |
| TB62300FG | Dual Full-Bridge Driver for DC Motor |
| TB62705CF | 8BIT SHIFT REGISTER, LATCHES & CONSTANT CURRENT DRIVERS |
| TB62705CFN | 8BIT SHIFT REGISTER, LATCHES & CONSTANT CURRENT DRIVERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB62206FG(EL) | 功能描述:馬達/運動/點火控制器和驅動器 Stepping Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB62206FG(O,EL) | 功能描述:馬達/運動/點火控制器和驅動器 2-Phase Bipolar IC 40V 1.8A POR RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB62207BFG(O,EL) | 制造商:Toshiba America Electronic Components 功能描述:2 STEPPER MOTOR DRIVE, 40V 1.5A HSOP36 制造商:Toshiba America Electronic Components 功能描述:2 Stepper Motor Drive 37V 2.5A TB62207BF |
| TB62207BFG(OEL) | 制造商:Toshiba America Electronic Components 功能描述:2 STEPPER MOTOR DRIVE 40V 1.5A HSOP36 |
| TB62208FG(O,8,EL) | 功能描述:馬達/運動/點火控制器和驅動器 BiCD 2-Phase Bipolar 40V 1.8A TSD ISD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。