- 您現在的位置：買賣IC網 > PDF目錄98166 > TB62201AF STEPPER MOTOR CONTROLLER, 1.5 A, PDSO38 PDF資料下載
參數資料
| 型號： | TB62201AF |
| 元件分類： | 運動控制電子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 1.5 A, PDSO38 |
| 封裝： | 0.450 INCH, 0.65 MM PITCH, HEAT SINK, PLASTIC, SOP-36/38 |
| 文件頁數： | 62/89頁 |
| 文件大?。?/td> | 1396K |
| 代理商： | TB62201AF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁當前第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁
TB62201AF
2005-04-04
65
Power Supply Sequence (Recommended)
Note 1: If the VDD drops to the level of the VDDR or below while the specified voltage is input to the VM pin, the IC is
internally reset. This is a protective measure against malfunction. Likewise, if the VM drops to the level of
the VMR or below while regulation voltage is input to the VDD, the IC is internally reset as a protective
measure against malfunction. To avoid malfunction, when turning on VM or VDD, we recommend you input
the RESET signal at the above timing.
It takes time for the output control charge pump circuit to stabilize. Wait up to tONG time after power on
before driving the motors.
Note 2: When the VM value is between 3.3 to 5.5 V, the internal reset is released, thus output may be on. In such a
case, the charge pump cannot drive stably because of insufficient voltage. We recommend the RESET state
be maintained until VM reaches 20 V or more.
Note 3: Since VDD = 0 V and VM = voltage within the rating are applied, output is turned off by internal reset. At that
time, a current of several mA flows due to the Pass between VM and VDD.
VDD (max)
VDD (min)
VDDR
GND
VM
VM (min)
VMR
GND
Non-
reset
RESET
H
L
RESET
VDD
VM
Internal
reset
RESET
input
…..*
Takes up to tONG until operable.
Non-operable area
t
相關PDF資料 |
PDF描述 |
|---|---|
| TB62206F | STEPPER MOTOR CONTROLLER, 1.8 A, PDSO22 |
| TB62209FG | STEPPER MOTOR CONTROLLER, 1.8 A, PDSO38 |
| TB62214FTG | STEPPER MOTOR CONTROLLER, 2 A, PQCC48 |
| TB62754AFNG | SWITCHING REGULATOR, PDSO20 |
| TB62756FUG | SWITCHING REGULATOR, 1430 kHz SWITCHING FREQ-MAX, PDSO6 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TB62201AFG | 制造商:Toshiba 功能描述:Stepper Motor Driver 5V 38-Pin (36+2Tab) HSOP 制造商:Toshiba 功能描述:Stepper Motor Driver 5V 38-Pin (36+2Tab) HSOP Cut Tape |
| TB62201AFG(EL) | 功能描述:馬達/運動/點火控制器和驅動器 Combination Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB62202AFG | 制造商:Toshiba America Electronic Components 功能描述: |
| TB62202AFG(EL) | 功能描述:馬達/運動/點火控制器和驅動器 Combination Motor Driver RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| TB62206FG | 制造商:Toshiba America Electronic Components 功能描述:2-Phase Stepping Motor Driver 5V 22-Pin(20+2Tab) HSOP |
發布緊急采購，3分鐘左右您將得到回復。