- 您現在的位置：買賣IC網 > PDF目錄98165 > TAS5708PHPR (TEXAS INSTRUMENTS INC) 20.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 PDF資料下載
參數資料
| 型號： | TAS5708PHPR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 音頻／視頻放大 |
| 英文描述： | 20.2 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| 封裝： | 7 X 7 MM, GREEN, PLASTIC, HTQFP-48 |
| 文件頁數： | 8/56頁 |
| 文件大?。?/td> | 1104K |
| 代理商： | TAS5708PHPR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
ERROR REPORTING
DEVICE PROTECTION SYSTEM
Overcurrent (OC) Protection
Overtemperature Protection
Undervoltage Protection (UVP) and Overvoltage Protection (OVP)
SERIAL DATA INTERFACE
CLOCK, AUTO DETECTION, and PLL
SLOS570 – DECEMBER 2008 ........................................................................................................................................................................................... www.ti.com
Any fault resulting in device shutdown is signaled by the FAULT pin going low (see Table 1). A sticky version of
this pin is available on D1 of register 0X02.
Table 1. FAULT Output States
FAULT
DESCRIPTION
0
Overcurrent (OC) ERROR
1
No faults (normal operation)
The device has independent, fast-reacting current detectors on all high-side and low-side power-stage FETs,
which protects against shorts across the load, to GND, or to PVCC. The protection system triggers a latching
shutdown, resulting in the power stage being set in the high-impedance (Hi-Z) state and FAULT being asserted
low. The device returns to normal operation once the fault condition (i.e., a short circuit on the output) is
removed. Current limiting and overcurrent protection are not independent for half-bridges. That is, if the
bridge-tied load between half-bridges A and B causes an overcurrent fault, half-bridges A, B, C, and D are shut
down.
The TAS5708 has an over-temperature protection system. If the device junction temperature exceeds 150°C
(nominal), the device is put into thermal shutdown, resulting in all half-bridge outputs being set in the
high-impedance (Hi-Z) state. The TAS5708 recovers automatically once the temperature drops approximately
15°.
THE UVP circuits of the TAS5708 fully protect the device in any power-up/down and brownout situation. The
UVP engages if PVCC_X = AVCC drops below 8.4-V (typical) and disengages when PVCC_X = AVCC exceeds
8.5-V. The OVP circuits protect aganist voltage spikes and engage when PVCC_X = AVCC exceeds 27.5-V
(typical). The OVP circuits disengage when PVCC_X = AVCC drops below 27.2-V. When the protection circuits
engage, all half-bridge outputs are immediately placed in the high-impedance (Hi-Z) state.
Serial data is input on SDIN. The PWM outputs are derived from SDIN. The TAS5708 DAP accepts serial data in
16-, 20-, or 24-bit left-justified, right-justified, and I2S serial data formats.
The TAS5708 is a slave device. It accepts MCLK, SCLK, and LRCLK. The digital audio processor (DAP)
supports all the sample rates and MCLK rates that are defined in the clock control register.
The TAS5708 checks to verify that SCLK is a specific value of 32 fS, 48 fS, or 64 fS. The DAP only supports a 1 ×
fS LRCLK. The timing relationship of these clocks to SDIN is shown in subsequent sections. The clock section
uses MCLK or the internal oscillator clock (when MCLK is unstable, out of range, or absent) to produce the
internal clock (DCLK) running at 512 times the PWM switching frequency.
The DAP can autodetect and set the internal clock control logic to the appropriate settings for all supported clock
rates as defined in the clock control register.
TAS5708 has robust clock error handling that uses the bulit-in trimmed oscillator clock to quickly detect
changes/errors. Once the system detects a clock change/error, it will mute the audio (through a single step mute)
and then force PLL to limp using the internal oscillator as a reference clock. Once the clocks are stable, the
system will auto detect the new rate and revert to normal operation. During this process, the default volume will
be restored in a single step (also called hard unmute). The ramp process can be programmed to ramp back
slowly (also called soft unmute) as defined in volume register (0X0E).
16
Copyright 2008, Texas Instruments Incorporated
Product Folder Link(s): TAS5708
相關PDF資料 |
PDF描述 |
|---|---|
| TAS5709AGPHPR | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5709AGPHP | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5709APHPR | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5709APHP | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
| TAS5709PHPG4 | 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP48 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TAS5709 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:20-W STEREO DIGITAL AUDIO POWER AMPLIFIER WITH EQ AND DRC |
| TAS5709APHP | 功能描述:音頻放大器 20W Stereo I2S Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5709APHPR | 功能描述:音頻放大器 20W Stereo I2S Aud Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
| TAS5709EVM | 功能描述:音頻 IC 開發工具 TAS5709EVM Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V |
| TAS5709PHP | 功能描述:音頻放大器 20W Stereo I2S input Aud Pwr Amp RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。