參數資料
型號： TAS5631PHD
廠商： TEXAS INSTRUMENTS INC
元件分類： 音頻／視頻放大
英文描述： AUDIO AMPLIFIER, PQFP64
封裝： GREEN, PLASTIC, HTQFP-64
文件頁數： 14/34頁
文件大小： 1823K
代理商： TAS5631PHD
www.ti.com
SLES221C – JULY 2009 – REVISED APRIL 2010
THEORY OF OPERATION
POWER SUPPLIES
To facilitate system design, the TAS5631 needs only a 12-V supply in addition to the (typical) 50-V power-stage
supply. An internal voltage regulator provides suitable voltage levels for the digital and low-voltage analog
circuitry. Additionally, all circuitry requiring a floating voltage supply, e.g., the high-side gate drive, is
accommodated by built-in bootstrap circuitry requiring only an external capacitor for each half-bridge.
To provide outstanding electrical and acoustical characteristics, the PWM signal path, including gate drive and
output stage, is designed as identical, independent half-bridges. For this reason, each half-bridge has separate
gate-drive supply pins (GVDD_X), bootstrap pins (BST_X), and power-stage supply pins (PVDD_X).
Furthermore, an additional pin (VDD) is provided as a supply for all common circuits. Although supplied from the
same 12-V source, it is highly recommended to separate GVDD_A, GVDD_B, GVDD_C, GVDD_D, and VDD on
the printed-circuit board (PCB) by RC filters (see application diagram for details). These RC filters provide the
recommended high-frequency isolation. Special attention should be paid to placing all decoupling capacitors as
close to their associated pins as possible. In general, inductance between the power supply pins and decoupling
capacitors must be avoided. (See reference board documentation for additional information.)
For a properly functioning bootstrap circuit, a small ceramic capacitor must be connected from each bootstrap pin
(BST_X) to the power-stage output pin (OUT_X). When the power-stage output is low, the bootstrap capacitor is
charged through an internal diode connected between the gate-drive power-supply pin (GVDD_X) and the
bootstrap pin. When the power-stage output is high, the bootstrap capacitor potential is shifted above the output
potential and thus provides a suitable voltage supply for the high-side gate driver. In an application with PWM
switching frequencies in the range from 300 kHz to 4000 kHz, it is recommended to use 33-nF ceramic
capacitors, size 0603 or 0805, for the bootstrap supply. These 33-nF capacitors ensure sufficient energy storage,
even during minimal PWM duty cycles, to keep the high-side power stage FET (LDMOS) fully turned on during
the remaining part of the PWM cycle.
Special attention should be paid to the power-stage power supply; this includes component selection, PCB
placement, and routing. As indicated, each half-bridge has independent power-stage supply pins (PVDD_X). For
optimal electrical performance, EMI compliance, and system reliability, it is important that each PVDD_X pin is
decoupled with a 2.2-mF ceramic capacitor placed as close as possible to each supply pin. It is recommended to
follow the PCB layout of the TAS5631 reference design. For additional information on recommended power
supply and required components, see the application diagrams in this data sheet.
The 12-V supply should be from a low-noise, low-output-impedance voltage regulator. Likewise, the 50-V
power-stage supply is assumed to have low output impedance and low noise. The power-supply sequence is not
critical as facilitated by the internal power-on-reset circuit. Moreover, the TAS5631 is fully protected against
erroneous power-stage turnon due to parasitic gate charging. Thus, voltage-supply ramp rates (dV/dt) are
non-critical within the specified range (see the Recommended Operating Conditions table of this data sheet).
SYSTEM POWER-UP/POWER-DOWN SEQUENCE
Powering Up
The TAS5631 does not require a power-up sequence. The outputs of the H-bridges remain in a high-impedance
state until the gate-drive supply voltage (GVDD_X) and VDD voltage are above the undervoltage protection
(UVP) voltage threshold (see the Electrical Characteristics table of this data sheet). Although not specifically
required, it is recommended to hold RESET in a low state while powering up the device. This allows an internal
circuit to charge the external bootstrap capacitors by enabling a weak pulldown of the half-bridge output.
Powering Down
The TAS5631 does not require a power-down sequence. The device remains fully operational as long as the
gate-drive supply (GVDD_X) voltage and VDD voltage are above the undervoltage protection (UVP) voltage
threshold (see the Electrical Characteristics table of this data sheet). Although not specifically required, it is a
good practice to hold RESET low during power down, thus preventing audible artifacts including pops or clicks.
Copyright 2009–2010, Texas Instruments Incorporated
21
Product Folder Link(s): TAS5631
相關PDF資料
PDF描述
TAS5701PAPG4 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64
TAS5701PAPRG4 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64
TAS5701PAPR 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64
TAS5701PAP 20 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64
TAS5704PAPRG4 20.6 W, 2 CHANNEL, AUDIO AMPLIFIER, PQFP64
相關代理商/技術參數
參數描述
TAS5631PHD2EVM 功能描述:音頻 IC 開發工具 TAS5631PHD Eval Mod RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
TAS5631PHDR 功能描述:音頻放大器 PWM inp 300W Stereo RoHS:否 制造商:STMicroelectronics 產品:General Purpose Audio Amplifiers 輸出類型:Digital 輸出功率: THD + 噪聲: 工作電源電壓:3.3 V 電源電流: 最大功率耗散: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:TQFP-64 封裝:Reel
TAS564K015P1A 制造商:Cornell Dubilier Electronics 功能描述:Cap Tant Solid 0.56uF 15V 10% (3.43 X 7.26mm) Axial 125°C T/R
TAS564K020P1A 制造商:Cornell Dubilier Electronics 功能描述:CAPACITOR TANT, 0.56UF, 20V, AXIAL 10%, Product Range:CORNELL DUBILIER - TAS Ser 制造商:Cornell Dubilier Electronics 功能描述:Cap Tant Solid 0.56uF 20V 10% (3.43 X 7.26mm) Axial 125°C T/R
TAS564K034P0A 制造商:Cornell Dubilier Electronics 功能描述: 制造商:Mallory Sonalert Products Inc 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*