- 您現在的位置：買賣IC網 > PDF目錄98159 > TAS5026APAGG4 (TEXAS INSTRUMENTS INC) SPECIALTY CONSUMER CIRCUIT, PQFP64 PDF資料下載
參數資料
| 型號： | TAS5026APAGG4 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| 封裝： | GREEN, PLASTIC, TQFP-64 |
| 文件頁數： | 16/64頁 |
| 文件大小： | 936K |
| 代理商： | TAS5026APAGG4 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
Architecture Overview
17
SLES068A—February 2003—Revised January 2004
TAS5026A
Because PDN is an asynchronous control signal, small clicks and pops can be produced during the application
(the leading edge) of this control. However, when PDN is released, the transition from the hard mute state back
to normal operation is performed synchronously using a quiet sequence.
If a completely quiet reset sequence is desired, MUTE should be applied before applying PDN.
2.2.2.1
Recovery Time Options
To support the requirements of various system configurations, the TAS5026A can come up to the normal state
after either a long (100 ms) or a short (5 ms) delay.
1.
In the first case, a slow system (95 ms to 100 ms) start-up occurs at the end of the power-down sequence
when:
RESET is high for at least 16 MCLK_IN periods before PDN goes high.
2.
Otherwise a fast (4 ms to 5 ms) start-up occurs.
NOTE: If MCLK_IN is not active when both of these signals are released high, then a fast
(4 ms to 5 ms) start-up occurs once MCLK_IN becomes active.
2.2.3 General Status Registers
The general status register is a read only register. This register provides an indication when a volume update
is in progress or one of the channels is inactive. The device id can be read using this register.
Volume update is in progress—Whenever a volume change is in progress due to a volume update
command or mute, this status bit is high.
Device identification code—The device identification code, 1 0011, is displayed.
No internal errors (all valid signals are high)—When there are no internal errors in the TAS5026A and all
outputs are valid, this status bit is high.
One or more valid signals are inactive—If low, one or more channels of the TAS5026A are not outputting
data. The Valid signals for those channels are inactive.
This can be produced by one of three causes:
One or more of the clock signals are in error
Error recover is active (low)
The automute has silenced one or more channels that are receiving 0 inputs
Mute has been set
Volume control has been set to full attenuation
If this signal is high, the TAS5026A is outputting data on all channels.
2.2.4 Error Status Register
The error status register indicates historical information on control signal changes and clock errors. This
register latches these indications when they occur. The indications are cleared by writing a 00(Hex) to the
register.
This register is intended as a diagnostic tool to be used only when the system is not operating correctly. This
is because the error status bits are set when the data rate, serial data interface format, or master/slave mode
is changed. As a result, this register indicates an error condition even though the system is operating normally.
This register should only be used while diagnosing transient error conditions.
Any clock error or control signal terminal change which occurs since the last time the error status register was
cleared is displayed. In using this register, the first step is to initialize the device and verify that all of the clock
signals are active. Then this register should be cleared by writing a 00(Hex). At this point, the register indicates
any errors or control signal changes.
相關PDF資料 |
PDF描述 |
|---|---|
| TAS5026APAG | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS5026APAGR | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS5026APAGRG4 | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS5026CPAG | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
| TAS5026PAGR | SPECIALTY CONSUMER CIRCUIT, PQFP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TAS5026APAGR | 功能描述:音頻 DSP 6Ch Dig Aud PWM Proc RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| TAS5026APAGRG4 | 功能描述:音頻 DSP 6Ch Dig Aud PWM Proc RoHS:否 制造商:Texas Instruments 工作電源電壓: 電源電流: 工作溫度范圍: 安裝風格: 封裝 / 箱體: 封裝:Tube |
| TAS5026CPAG | 制造商:TI 制造商全稱:Texas Instruments 功能描述:SIX CHANNEL DIGITAL AUDIO PWM PROCESSOR |
| TAS5026IPAG | 功能描述:多媒體雜項 Dig Aud PWM Proc RoHS:否 制造商:Texas Instruments 類型: 通道數量: 轉換速率:540 Mbps 分辨率: 封裝 / 箱體:SOIC-16 封裝:Tube |
| TAS5026IPAGG4 | 功能描述:多媒體雜項 Dig Aud PWM Proc RoHS:否 制造商:Texas Instruments 類型: 通道數量: 轉換速率:540 Mbps 分辨率: 封裝 / 箱體:SOIC-16 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。