- 您現在的位置：買賣IC網 > PDF目錄3849 > T89C5115-TISIM (Atmel)IC 8051 MCU FLASH 16K 28SOIC PDF資料下載
參數資料
| 型號： | T89C5115-TISIM |
| 廠商： | Atmel |
| 文件頁數： | 65/113頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 8051 MCU FLASH 16K 28SOIC |
| 標準包裝： | 27 |
| 系列： | 89C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 40MHz |
| 連通性： | UART/USART |
| 外圍設備： | POR，PWM，WDT |
| 輸入/輸出數： | 20 |
| 程序存儲器容量： | 16KB（16K x 8） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 2K x 8 |
| RAM 容量： | 512 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 3 V ~ 5.5 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁當前第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁
55
AT89C5115
4128G–8051–02/08
Timers/Counters
The T89C5115 implements two general-purpose, 16-bit Timers/Counters. Such are
identified as Timer 0 and Timer 1, and can be independently configured to operate in a
variety of modes as a Timer or an event Counter. When operating as a Timer, the
Timer/Counter runs for a programmed length of time, then issues an interrupt request.
When operating as a Counter, the Timer/Counter counts negative transitions on an
external pin. After a preset number of counts, the Counter issues an interrupt request.
The various operating modes of each Timer/Counter are described in the following
sections.
Timer/Counter
Operations
A basic operation is Timer registers THx and TLx (x = 0, 1) connected in cascade to
form a 16-bit Timer. Setting the run control bit (TRx) in TCON register (See Figure 37)
turns the Timer on by allowing the selected input to increment TLx. When TLx overflows
it increments THx; when THx overflows it sets the Timer overflow flag (TFx) in TCON
register. Setting the TRx does not clear the THx and TLx Timer registers. Timer regis-
ters can be accessed to obtain the current count or to enter preset values. They can be
read at any time but TRx bit must be cleared to preset their values, otherwise the behav-
ior of the Timer/Counter is unpredictable.
The C/Tx# control bit selects Timer operation or Counter operation by selecting the
divided-down peripheral clock or external pin Tx as the source for the counted signal.
TRx bit must be cleared when changing the mode of operation, otherwise the behavior
of the Timer/Counter is unpredictable.
For Timer operation (C/Tx# = 0), the Timer register counts the divided-down peripheral
clock. The Timer register is incremented once every peripheral cycle (6 peripheral clock
periods). The Timer clock rate is fPER/6, i.e. fOSC/12 in standard mode or fOSC/6 in X2
Mode.
For Counter operation (C/Tx# = 1), the Timer register counts the negative transitions on
the Tx external input pin. The external input is sampled every peripheral cycles. When
the sample is high in one cycle and low in the next one, the Counter is incremented.
Since it takes 2 cycles (12 peripheral clock periods) to recognize a negative transition,
the maximum count rate is fPER/12, i.e. fOSC/24 in standard mode or fOSC/12 in X2 Mode.
There are no restrictions on the duty cycle of the external input signal, but to ensure that
a given level is sampled at least once before it changes, it should be held for at least
one full peripheral cycle.
Timer 0
Timer 0 functions as either a Timer or event Counter in four modes of operation.
Timer 0 is controlled by the four lower bits of TMOD register (See Figure 38) and bits 0,
1, 4 and 5 of TCON register (See Figure 37). TMOD register selects the method of
Timer gating (GATE0), Timer or Counter operation (T/C0#) and mode of operation (M10
and M00). TCON register provides Timer 0 control functions: overflow flag (TF0), run
control bit (TR0), interrupt flag (IE0) and interrupt type control bit (IT0).
For normal Timer operation (GATE0 = 0), setting TR0 allows TL0 to be incremented by
the selected input. Setting GATE0 and TR0 allows external pin INT0# to control Timer
operation.
Timer 0 overflow (count rolls over from all 1s to all 0s) sets TF0 flag generating an inter-
rupt request.
It is important to stop Timer/Counter before changing mode.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC18F27J13-I/SP | IC PIC MCU 128KB FLASH 28SPDIP |
| T89C5115-TDSIM | IC 8051 MCU FLASH 16K 24SOIC |
| 52893-2090 | CONN FFC 20POS .50MM R/A ZIF SMD |
| T89C5115-SISIM | IC 8051 MCU FLASH 16K 28PLCC |
| 52893-1990 | CONN FFC 19POS .50MM R/A ZIF SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T89C5115-TISUM | 功能描述:IC 8051 MCU FLASH 16K 28SOIC RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:89C 標準包裝:1,500 系列:AVR® ATtiny 核心處理器:AVR 芯體尺寸:8-位 速度:16MHz 連通性:I²C，LIN，SPI，UART/USART，USI 外圍設備:欠壓檢測/復位，POR，PWM，溫度傳感器，WDT 輸入/輸出數:16 程序存儲器容量:8KB（4K x 16） 程序存儲器類型:閃存 EEPROM 大小:512 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 125°C 封裝/外殼:20-SOIC（0.295"，7.50mm 寬） 包裝:帶卷 (TR) |
| T89C5121 | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with MULTI-PROTOCOL SMART CARD INTERFACE |
| T89C5121-ICRIL | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with MULTI-PROTOCOL SMART CARD INTERFACE |
| T89C5121-ICSIL | 制造商:ATMEL 制造商全稱:ATMEL Corporation 功能描述:8-bit Microcontroller with Multi protocol SMART Card Interface |
| T89C5121-ICSUL | 制造商:Atmel Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。