- 您現在的位置：買賣IC網 > PDF目錄382571 > T7234 (Lineage Power) ISDN Transceiver(ISDN收發器) PDF資料下載
參數資料
| 型號： | T7234 |
| 廠商： | Lineage Power |
| 英文描述： | ISDN Transceiver(ISDN收發器) |
| 中文描述： | 綜合業務數字網收發器（綜合業務數字網收發器） |
| 文件頁數： | 5/36頁 |
| 文件大?。?/td> | 697K |
| 代理商： | T7234 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Lucent Technologies Inc.
3
Manual
May 1996
SCNT1 Family Reference Design Board
Hardware User’s Manual
Description
(continued)
Circuits
The following sections discuss the circuits found in
Figure 4.
U-Interface
The U-interface attaches to the board at RJ-45 connec-
tor J1 (see Figure 3). F1 and VR2 provide overcurrent
and overvoltage protection, respectively. These two
devices in combination with transformer T1 provide
protection levels required by FCC Part 68 and
UL* 1950. C16 is a 1.0 μF dc blocking capacitor that is
required per ANSI T1.601, section 7.5.2.3. The 250 V
rating of C16 is governed by the maximum breakdown
voltage of VR2, since the capacitor must not break
down before VR2. The resistance of R13 (21
) and F1
(12
) provide a total line-side resistance of 33
,
which is required when using the Lucent Technologies
2754H2 transformer. An alternate footprint is provided
that accepts the Valor
PT4084 U-interface trans-
former.
When the Valor transformer is used, R13 should be
changed to 18.2
. In general, the total line-side resis-
tance requirement, RL, is determined by the following
equation, where Rp is the primary (device-side) wind-
ing resistance of the U-interface transformer and Rs is
the secondary (line-side) winding resistance of the
transformer.
RL = 58.14 – 2.25 Rp – Rs
* ULis a registered trademark of Underwriters Laboratories, Inc.
Valor is a registered trademark of Valor Electronics, Inc.
On the device side of the U-interface transformer, VR1
provides secondary overvoltage protection of 6.8 V.
Optional capacitors C13 and C14 provide common-
mode noise suppression for applications that are
required to operate in the presence of high common-
mode noise. R8 and R9 provide the necessary external
hybrid resistors.
MLT Circuit
The metallic loop termination (MLT) circuit (U3 and
related components) provides a dc termination for the
loop, per ANSI T1.601, section 7.5. R14 and R15 are
power resistors used to sink current during over-
voltage fault conditions. U2 provides signal isolation
and voltage translation of the signaling pulses used for
NT maintenance modes, per T1.601, section 6.5. The
Lucent Technologies T7234, T7237, and T7256
devices interpret these pulses via an internal ANSI
maintenance state machine, and respond accordingly.
For applications outside North America, the MLT circuit
is not needed and can be disabled by simply removing
U3 from its socket.
相關PDF資料 |
PDF描述 |
|---|---|
| T7237 | ISDN Transceiver(ISDN收發器) |
| T7264 | U-Interface 2B1Q Transceiver(U接口 2B1Q收發器) |
| T7264 | T7264 U-Interface 2B1Q Transceiver |
| T7289A | DS1 Line Interface(DS1 線接口) |
| T8207 | Asychronous Transfer Mode (ATM) Interconnect(異步傳輸模式互連器件) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| T7234A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Compliance with the New ETSI PSD Requirement |
| T7237 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Compliance with the New ETSI PSD Requirement |
| T7237A | 制造商:AGERE 制造商全稱:AGERE 功能描述:Compliance with the New ETSI PSD Requirement |
| T7240 | 制造商:TE Connectivity 功能描述: |
| T7-241A5 | 功能描述:撥動開關 ON NONE OFF 2 Pole Standard Bat Handle RoHS:否 制造商:OTTO 觸點形式: 開關功能: 電流額定值: 電壓額定值 AC: 電壓額定值 DC: 功率額定值: 端接類型: 安裝風格: 端子密封: 觸點電鍍: 照明: |
發布緊急采購，3分鐘左右您將得到回復。